Sam's is your source for Hatteras and Cabo Yacht parts.

Enter a part description OR part number to search the Hatteras/Cabo parts catalog:

Email Sam's or call 1-800-678-9230 to order parts.

Pee ohd at PO's

  • Thread starter Thread starter Mike36c
  • Start date Start date
  • Replies Replies 38
  • Views Views 12,566

Mike36c

Well-known member
Joined
Apr 12, 2005
Messages
731
Hatteras Model
36' CONVERTIBLE-Series I (1969 -1977)
I'm finding all kinds of crazy things on this boat I just purchased, thought it might be fun to post some of stuff we all find. Here's a pic of what I found under the mid bilge hatch. Also, the boat has a battery switch switching two large ground wires, have yet to figure out how it works. Anyway, here we go.
 

Attachments

  • IMG_0677.webp
    IMG_0677.webp
    47.8 KB · Views: 303
Make sure you trace those wires on those battery switches they may be positives even though they are black. I don't understand why a big boat builder(Hatteras included) can't buy some red wire to wire their boats instead of using black for pos and neg. most good newer boats use the yellow ground, red pos. Scheme through out which make things much easier to trouble shoot. John
 
What did the survey find? Or miss?

Was that noted in the survey.
 
Make sure you trace those wires on those battery switches they may be positives even though they are black. I don't understand why a big boat builder(Hatteras included) can't buy some red wire to wire their boats instead of using black for pos and neg. most good newer boats use the yellow ground, red pos. Scheme through out which make things much easier to trouble shoot. John

The PO set up an inverter that can run off the house batteries or the starboard engine battery, set to both the engine can charge them all while underway which is cool but right next to that switch is another battery switch that connects to the same battery bank grounds. Why in the world would anyone do this? It's all 12 volts. Check out this zinc that was nearly welded in place, and the economy fitting on the other gear cooler.
 

Attachments

  • IMG_0474.webp
    IMG_0474.webp
    37.9 KB · Views: 267
  • IMG_0470.webp
    IMG_0470.webp
    31.3 KB · Views: 273
What is that coming out of the top photo?
 
Looks like a sea slug.Or an old Babe Ruth. Where is Bill Murray when ya need him?
 
No kidding. My boat still has all these small holes in the woodwork from all these little brass plaques that were attached, things like "The captain's always right" etc etc. Must have been three or four of them. Plus they threw out the original Hatteras settee in the salon and put a futon there. And don't even get me started on the wiring. Horrible. No charging returns for any of the batteries- everything went back to the charger through one twelve gauge wire. Which was usually too hot to touch. crazy.
 
I never understood why people love to drill holes in boats for unnecessary stuff. It seems to occur the most in interior woodwork, exterior decks (screws or holes to leak), the transom, and of course the hull and hull sides. 50% of the holes could be avoided with some thinking.
 
Just a guess but was the PO European because many boats built in Europe like Beneautus etc had shut offs on both positive and ground leads. Interesting that the boats from these European countries that are built in there US plants do not have ground disconnects. John
 
Some of the "engineering" I found when I first purchased my boat. The bilge is looking much better these days.

"Bilge pump wiring"
"Plastic thru hull" - yes, it is below the waterline
"Soda can pipe support"
 

Attachments

  • DSCF1917.webp
    DSCF1917.webp
    52.7 KB · Views: 154
  • DSCF1916.webp
    DSCF1916.webp
    37.6 KB · Views: 154
  • DSCF1915.webp
    DSCF1915.webp
    37.7 KB · Views: 154
Is that soda can holding up the pipe?
 
Just a guess but was the PO European because many boats built in Europe like Beneautus etc had shut offs on both positive and ground leads. Interesting that the boats from these European countries that are built in there US plants do not have ground disconnects. John

That is because many boats built in Europe use a floating ground system hence the switches on the ground wires. I once had an aluminum sailboat built in Holland with such a floating ground thus isolating the electrical system from the aluminum hull. I converted it to a grounded system to the engine and hull and eliminated the ground wire circuit breakers...much less compicated in my opinion.
 
Is that soda can holding up the pipe?

It was a mutual thing. The soda can was holding up the pipe,
and the pipe was holding the soda can in place. ;-)
 
Just goes to show how things have changed. Today's soda cans are not strong enough.
 
Just goes to show how things have changed. Today's soda cans are not strong enough.

Now thats just wrong. Especially since the coast guard requires wires in an engine area to be supported with metal devices.
 
That pipe is held up with a metal device.

Tim
 
I could see how it could work, but it's not even a name brand cola. A Hat deserves better.
 
As I find myself saying so often, Amazing, Just F---ing Amazing. And I have done my very best to bring my 55' C I am selling up to speed, but the next owner will find things I'm sure.
 

Forum statistics

Threads
38,154
Messages
448,703
Members
12,482
Latest member
UnaVida

Latest Posts

Trending content

Back
Top Bottom