Search results

Our 3/4 full lights in all 4 heads remain on constantly. Has been this way since purchased 3 yrs ago. Removed bulbs to “fix”.Finally got motivated to chase the issue. Located pressure switch in forward Bilge area and as suspected it crumbled in my hands…. Replaced with a Groco AS100 but no...

At my Pilot House helm I have the 4 traditional Bilge switches for FWD, AFT, Port and Starboard bilges. I also have a single switch directly behind the wheel and to the right labeled “Bilge Pump”. I can’t seem to locate what it controls. It has power and illuminates when I place in manual or...

1985 61MY 3/4 full warning lights all 4 illuminate constantly. Trying to locate the par pressure switch. I can see the location where the tube exits the holding tank but because of the location (behind the aft generator) I can’t get to it to trace the tube.I have checked all hatches in...

New dual station sender installed on both Engines... ENGINE BLOCK HEATERS HAVE BEEN ON... Port gauges preform as expected on both pilothouse and flybridge. Upon switching ignition on, both slowly rise to around 130° and return to zero when switched off. Starboard (I might add that they have...

Looking for a friend: In need of a 60lb hinged stainless plow anchor, in the under $1500 range... Have located several online BUT everyone seems to be "out of stock" at the moment. His current one was damaged and has zero markings/manufacturer info on it. Thanks

I need to replace 8 forward Starboard stanchions (don’t ask, dumb mistake) on our 1985 61’ MY starting just forward of the stair entryway. Fortunately the teak railing and stainless end caps were undamaged. Would need entire stanchions (base, upright and clip to attach teak). I have reached out...

Recently updated several hatches which had been covered by carpet in our companion way when we updated to LVP. I used this product and was very pleased with the outcome https://www.jonnycorners.com/

Can someone tell me the name of the material used to fill the gaps in pass throughs in the engine and generator rooms? It is the black sticky material I have tried to search everything I can think of

1985 61 MYNot able to measure at this time. Does anyone have knowledge of the length of the mechanical sight gauges for the forward and aft fuel tanks? I believe they are 1.5”npt and suspect by my memory that they are 36”???

Does Sterling offer a Bluetooth module? I know I have seen somewhere that there was one and an app but cannot seem to locate? Trying to monitor from Flybridge, I guess I could always install a 2nd remote? Thanks

As a follow up: Removed carpet and BOOM, hatches were in place and intact... Polished both tanks with system I made based off of a unit another user made (pic attached) sorry I can't remember who it was... Replaced carpet with LVT and installed Johnny Corners hardware (pic attached) All good...

Looking for advice on temp sensors…. Have single stud sensors what are the recommended replacements? Thanks

I am looking for flat bar stainless corner trim for hatch covers... see pic. Any ideas, I have searched google and cannot seem to find anything...

Looking for a part number for a rebuild kit for the Hynautic H42-04S pump. I researched and saw a post by "Southern Comfort" on here who has the same pump and vessel (1985 61 MY) that he had one and the recommended kit number HS-04 did not fit his unit, however he did not elaborate on which kit...

Thank you... Have pretty much determined that the floor in the companionway will be "modified" with better access to tank gauge areas. Does anyone by chance have dimensions on what was original on these older Hatteras vessels for that? I will most likely put square/rectangular openings here...

A little background: 1985 61' MY w/ 12v71s Purchased vessel in 2022. Have dual 1000 racors on each engine. According to PO he never utilized the forward fuel tank, always ran on aft tank. He owned the boat for 6 yrs. Don't know why he didn't alternate. Fuel gauge shows full in forward...

Have a friend with a Hatteras and his aft and mid electric heads won’t cut off when flushed on fresh water. Water continuously runs into bowl. They work properly when switched to raw water.

Went to get off the dock on Saturday and upon starting the port side noticed alt meter was pulsing, as if something was drawing, requesting current. No pattern to it just randomly. Went down to ER and heard clicking which matched the pulsing. Quickly shut it down and had the "first mate"...

Looking for a Furuno RD30 to replace a unit with screen burn…. This is a temporary fix, as I plan to upgrade to the RD33 or Garmin GMI 20 systems thanks

1985 61MY and the older LaMarche is on it's last leg. Have 2 - 32v banks, starboard starting and port starting/house. Current marina setup is 2 - 50a inputs. Would like to replace with a smart charger and looking for recommendations. I have researched and found several options, just not...