Search results

Has anyone on here tried Linseed oil on their outside teak decking? Searched the posts here and didn't see any posts about it.

My Intrepid was totaled in the Ian so I happened to be looking online.....never a good thing as it always cost money...and found an immaculate fresh water Formula 33 that I will close on Tuesday of next week. It has a few issues, most from very low usage..one being the the head was not emptied...

My Intrepid 32 was totaled in Ian and is still resting up against my house, my neighbors boat and his house. The adjuster won't be out to look at it until Nov. 30! I have sent pics to them and my marina up north for their opinion on if it can be fixed and for how much it would cost. My question...

I have a high preasure switch that has gone bad on one of my A/C units. Cruise Air 7k btu compressor low is 150 high is 300psi. It had Klixon 325 on it that went south not able to find any of those. I have found Johnson Controls P100cp-166c units online that are 225 on and 325 off I ordered two...

In forty years of boating I don’t think I’ve put as much as a scratch on a boat. As of this past Monday I can no longer say that. The starboard twin disc transmission stuck in forward during a fuel stop. The result in close quarters was 93,000 pounds landing on an older fiberglass Chris-Craft...

My salon Cruiseair SMX II sounds a beeping alarm every morning at the same time shutting it off. If you just hit the cool button it goes back to work as if nothing ever happened and runs fine until the same time the next morning when it does it again! Thoughts or a solution? Thanks in advance!

I had my prop's off to replace the cutlass bearings so they were sent out to Prop Scan to take a look at. They determined that the leading edge was high and the trailing edges were low. They would be happy to adjust them back to normal for the low price of $2,700 each! My question to any prop...

I have a dead cell in one of four 8v195 batteries used to fire up my Detroit 16v92 DDEC engines. Deka has stopped making them. I have sourced four at a exorbitant price. The batteries where only two years old. Has anyone come up with a solution for a 32v system as a replacement for the 8v195 as...

Over the winter I had all of the old electronics on the helm taken out and replaced with new units. The old sat phone system and several old gps antennas, non functioning single sideband radio, radar and display, old ray marine unit, old camera system and display removed, DDEC displays moved and...

Has anyone made that trip and if so what is the best route with fuel/marinas to stop in. Time of year best for the trip...etc

I have read the old posts on this subject and don't see much of any mention of Stanadyne being used. Just wondering why as I have heard many positives about its use from people outside the marine industry. I am going to start using something next spring in my 16v92 Detroits and want to make sure...

I have the Allen Bradley push button's on my heads and one of them is not working correctly. Does anyone know where to source just the momentary switch? I see Razz Marine has the whole switch plate including emergency switch but I really only need the push button and I'm sure they are very proud...

I purchased a used Pursuit in FL and to pull it back to MI this past spring. I also purchased a NEW Continental trailer in FL. The trailer was a POS!! On the trip home the brakes didn't work, the hitch had the wrong bolts..too small for the holes..causing it to droop about 1.5 inches.., one...

WW Williams is suggesting to run 10 micron Part# 2353 0408 at the end and beginning of the season to clean out any dirt in the oil and then switch to Part# 2353 0407 which are the 30 micron for the season. This is a new one on me has anyone else done this or heard of it?? Good way to increase...

16v92s running at 1,850 rpm for about 45 min. and the port engine stumbles about 40 or so rpm just out of the blue....it recovered but showed a bit of floating rpm ..by 10 or 15 on the ddec but did return to normal operation. During this I'm checking engine load, fuel pressure etc on both...

Cruise Air cooling pump won’t shut off My salon AC unit, when power is on to it runs the cooling pump contiually even if the unit is shut off.The only way to shut down the cooling pump is to kill the breaker to that unit. The pump then cycles properly for the othe units on board. The AC guy has...

Has anyone replaced them ? I changed impellers the other day on my new to me Bertram and one of the inserts is pretty beat up!!! They appear to be in there very tight!

Hot water heater on my Bertram worked fine going into storage now heater not working. Breaker has 240 to it but when turned on drops to 0 on the back side. If I unhook wires at heater I’m only reading 89 volt at the wires at the heater no old in hooked. IMput please from the electrical wizards...

Does anyone have knowledge or experience with Norestar anchors....good/bad?