Search results

1980 43' DCFB - a nice go-to-sea boat in great condition and exceptionally clean Queen bed in stateroom 6-71 TIs - 390 HP Westerbeke 7.6 GEN 3 burner Princess stove with oven, micro-wave, full size refrigerator. 2 Cruisair AC-Heating systems Vacuflush heads Well equipped for west...

Here is a very nice 1980 Hatteras 43 in San Francisco Bay. http://www.yachtworld.com/boats/1980/Hatteras-Double-Cabin-2629753/pittsburg/CA/United-States Will

1980 43' DCFB - a nice go-to-sea boat in great condition Queen bed in stateroom 6-71 TIs - 390 HP Westerbeke 7.6 GEN 3 burner Princess stove with oven, micro-wave, full size refrigerator. 2 Cruisair AC-Heating systems Vacuflush heads Well equipped for west coast (San Francisco) Cruising...

My Simrad auto pilot works perfectly under all conditions except 2ft plus following seas where it makes the boat (a 43'DC) zig and zag like crazy. Has anyone been able to get theirs to control the boat better under such conditions? Thanks - Will

Per the June/July 2011 issue of the magazine Professional Mariner, Marine Inland Fabricators (MIF) in Panama City, Florida, recently built a small tug powered by twin 6-71s and a ferry powered by an 8V-71. Both boats are going to Nigeria. Will

1980 43' DCFB. I'm interested in removing the exterior teak hand rails to strip and varnish. It looks to be straight forward but I'm concerned about removing the stainless steel end caps. It looks as if the caps are slid over the ends of the teak railings then secured with two screws on the...

Does anyone have experience with reducing exhaust fumes entering the cockpit or aft deck? Many newer boats have exhaust exiting on the sides near the stern and some have deflectors on stern exhausts, directing gases to the sides. Have any of you folks tried converting to these options? The...

How do you install a Jabsco Sea Water Pump on a 6-71 TIB? I'm having problems getting the pump drive gear to mesh with the inside of the coupling gear which turn, slides into a multi-tooth socket on one of the gear train gears. The pump was removed from the drive plate adapter which is still...

An update !!! Problem was not the oil cooler at all. It turns out that the gear box vent is under the Sea Water pump and dip stick tube is on the side. A water leak developed in the pump's cover plate spraying water into the vicinity of both. Good thing it happened because removing the...

This anchor alarm app for cell phones looks pretty cool. Between the depth sounder, radar and GPS plotter, I have sources for anchor watch alarms but nothing with with alarms loud enough to hear from the cabin. Have any of you folks tried one ? http://www.myanchorwatch.com/Default.aspx...

43' DC with 485 HP 6-71 TIs. I noticed about 1/4 in. of the shaft key sticking out behind the coupling to the trans. and was able to push it back in without resistance. The center nut holding the coupling to the shaft seems to be tight. I'm told it's the coupling to shaft taper that takes the...

What kind of 110V pumps are people using for their anchor washdown systems? I can accommodate up to 1/2 H.P. Thank you Will

Our 1980 43' Double Cabin is powered by 485 HP, 6-71 TIBs with 1.51:1 gear boxes. Hatteras put 24D x 23P, 4 blade props on the boat. What reduction gears ratios and prop sizes did they put on other 6-71 (6-71 N's, 6-71 TIs, etc.) powered 43' DCs? Just curious - Will

I need a photo showing original colors of the pointer and the scale of an AC Delco 12 v volt gauge (the one on an engine gauge panel). If anyone has such a guage in good condition, I'd appreciate a photo of it. Otherwise, does anyone know where I can see a photo of one. Thanks - Will

vindentc 6-71ti's and jaxfishgyd 6-71ns both report using 6GPH @ 9 kts. while I calculate 10 GPH @ 9kts (1200 RPM for me). I don't know if their readings are by calculation or FloScans. I see no fuel leaks, smoke, soot, etc. I have 1.5:1 gear boxes and both engine WOT at about 2350 RPM under...

One of my Rudder indicator meters is broken. It's about 2.5" dia. says "Dyna Marine" on the dial and they are no longer around. Essentially, it just seems to be an analog millivolt meter. I measured input from the sender and it was plus 205 mv at right full rudder, 0 mv at midships and minus...

The top of the center widshield on my 43' DC opens but I'm not sure about the bottom part. The bottom looks like it may hinged at the bottom to open outward and downward but I'm not sure. Also, the outside frame of the lower window has screws around it that look like if removed, the frame...

I'm installing new windshield windows on a 1980 43' DCFB and am having problems with the material I ordered from SAM's. (This is not a complaint against SAM's) There didn't seem to be any backing on the two side windows when I removed them. But, the center one did have a rubbery substance as...

My trim tabs were replaced at one time and I'm not sure they are installed properly. Hydraulic cylinder travel is normal but I'm not sure that they are mounted in the correct position with respect to the tabs. They are attached to the tabs at the outside edge which is probably correct...

Does anyone have a source parts source for a 1980 Optimus Princess 3 burner stove? I need a rotary burner control and SAM's can get them. ps. I thought I posted this before but somehow lost it. Must be old age. Thanks - Will