Search results

Ive got A 1981 37C with DD 671 TI JT, trying to replace the Rt engine throttle cable with new. I can not find the model number on either end. I did call Sams and they have identified about 7 different cables under my hull number 415. However it does not say what position each of the cables...

A few days ago my norpro yanmar 8kw stopped running. At first I could hear the motor slowing down. I shut it down at the switch because it sounded as though it was going to quit anyways. It was slowing down, as if there was a heavy load. Now, I’ve restarted it twice, but it cut off within...

Has anyone installed one of these water heaters. It's smaller than its replacement. Just wondering if anyone can tell me if the mixing valve extends the hot water out long enough to get a shower, estimate of shower time would be helpful thanks

Damn, this water heater has sprung a leak and burned the power wires. Bigger problem is how to get it out of my port side engine room and what to put in its place: any ideas? Pictures sideways until I figure out rotation, sorry

It has been several weeks since I fired up the Top Dog. After I looked at all the gauges, I noticed that the starboard altinator was redwing 12 volts, port was reading 14. I hit the parell switch and the starboard showed 14. Moments later I noticed that all the gushes on the starboard side...

Over the past year I've been trying to find a leak in my hynautic steering system. Found the leak and replaced the 3/8 copper line in the aft bildge. Now I'm trying to purge the system. After reviewing the tips and tricks I still am not sure where to bleed the system. This is a picture of my...

On my starboard 671 TI the 205 degree Sensor was starting to separate, maybe from being steped on or floor board dropping. I ordered another one and here is a picture of both of the sensors. They look different, they are different sizes and different metal... Does anyone know if they work the...

So my starboard dripless drive shaft is dripping. I have a back up seal on the drive shaft ready to install. See pictures. I'm not sure how to get the old seal out. I have removed the spiral retaining ring. This unit is a strong seal, so to replace the seal, how do you get the old seal out...

With all the cruddy weather over the past few months I neglected to run my motors. I've been waiting for some warmer decent weather. So today was the day. Initially, the right motor started up after a prolonged start sequence, no problem. Left motor put out a few puffs of smoke, acted like...

On my JT 671 TI engine seriall/model # there is a star at the end! what does it mean?

Does any one recognize these block heaters. Both are bad. Corrosion has set in and when I turn them on at the breaker, I can hear an electrical arcing at the probe. I have JT 671TI in my 1981 37C. The probes are installed just behind what appears to be a fuel pump(not positive). Pictures...

http://okaloosa.craigslist.org/boa/4673287823.html Nice little project

I made a huge blunder. I pulled my refrigerator out to pull a cable and forgot to reset the circuit breaker back on. Consequently the bait in frig has fouled. I cleaned it out with soap and Clorox. Is there any way to save this frig.

Pictures are of my salon Cruisair circuit breaker box. 16000 btu. It's on my 1981 37C. 120 volts.

I have a 1981 37c. Several years ago the po installed a hard top and did not reinstall an antenna, atleast I have not found one. I have install two flat scenes and are using rabbit ears but only get 5 or so channels. So I purchased a Shakespeare Sea Watch model 3020 and plan to install it on...

This afternoon I decided to clean out the drawers and hatches in my v-berth compartments. When opening the hatch in the floor, I was surprised to see about 2 inches of water. I vacuumed the water out and scrubbed it with fresh water and soap and re vacuumed. But what is the thing just next...

As shown in these pictures. Does anyone have these in their boat. Where would I find these bulbs. Has anyone changed these fixtures to something better.

I'm out in my 37C with the anchor down and my windless will not operate. The solenoid has power, but the windless doesn't show signs of life. I have attached some picture. I'm not sure what the small black lever on the side does, maybe someone can tell me. I think it's causing the windless...

The good news is, the circuit beaker did it's job and immediately tripped when the short or heat was detected. Next, maybe I can get some ideas from you guys on how extensive the repair show be after looking at the pictures. The white wire going to the circuit breaker that has a burn will be...

http://miami.craigslist.org/mdc/boa/4521451040.html Just incase you may be interested