Search results

Had turbos rebuilt 2 years ago. Looks like the stainless riser sprung a leak. It’s now fused / rusted to the manifold. I need to get it off and new one made. I’ve beat on it with hammer. Used small chisle used pb blaster and it’s stuck solid. How would you go about getting it off. Turbo was...

Well, Looks someone did a hit and run on me last weekend. There was a transient parked next to me for a couple days (50+ 'Searay) But whoever did it, left like a 30' gouge down the port side. Some into the glass. About 2 foot or so above the water line. Question, Where do I get it spray...

8v92's twin turbos. 1991 Looks like I'm getting soot on the fresh water side. I run distilled water and Napa Cool. has black almost like oil looking stuff. Put finger in, and when you rub it. stuff goes away Also leaving a little black some on horizon, and cockpit / transom area is now getting a...

The Department of Transport, Tourism and Sport has advise it has been informed that Kannad Marine, the manufacturer of Kannad SAFELINK EPIRBS, have issued a Global Recall Safety Notice of the following affected EPIRB units: Part No.’s Affected Description Date Range K1202311 EPIRB SAFELINK...

Cable snapped on the Marquipt Tender Lift 1500 / Classic Any idea as to how to replace / route a new cable? I have the manual, but it does not go into details on how to replace Thanks

Having a new mast built by seaviewglobal (PYI, Inc) Here is the drawing they sent of final product. Will be hinged, and handle a 6ft open array Also, color matched to the newly painted arch

Finished bottom job May 10, splashed May 12 Took off and went to Abaco for a month Yea, Got loud stereo on the FlyBridge

Hauled the boat out last weds to get ready for trip to the islands in may. Found a bunch of what I guess you call blisters, but they are not really blisters in the sense they they hold no water/styrene? They are all dry, and there is dry fiberglass stands showing Should I worry? I ground a few...

Hi, what exactly do these things do? they are screwed in on one side, the other side is or was held in place with I guess 5200 They are lose on the aft side, the forward side is held in place with some screws Do I need to remove and rebed? I'm able to move the aft side downward appox 1/8" or so

How do you get the davit off? it's a Marquipt Tender-Lift 1000/1500 Classic Does it just lift off the standpipe? I'd like to grease the bearing etc How heavy is this thing? Any thing special needs to be done before trying to get it off

Are these Aluminium I-Beams on Dingy deck Factory or installed at some other point in time They seem a little over kill for a dingy, unless at one time there was something else installed up here they run the entire length and then the side pieces at the aft are welded to the long pieces. Then...

Kinda of out of order but while removing arch also having new screens / back enclosure and cockpit shade installed. Should have waited for the arch to be removed before canvas guy started but oh well. Also, got a new 58' Hatteras as a new neighbor last month. Has a nice jet boat for a dingy

Any of you experts know what model Cat pump this is? I contacted SeaRecovery and they want 240 for O-Rings, and 570 for valve o-ring kit. I heard of some markups but that is crazy. Pretty sure I can just get a new pump for around 1500.00 Of course it's been re-branded by SeaRecovery so I can...

Anyone know if there is a guide on how to measure for the marquipt sea stairs not sure if I need a 7 or 8 step. I don't see any guides or install directions on the marquipt site thanks or any advice on how to tell :)

Hi All, have 3 vacuflush toilets plumbed into a center line holding tank. Appox 85 gals give or take. Just realized yesterday that the red lights in the heads are not working . they are supposed to warn on 3/4 tank full. Question is, how do I test the sender unit on the tank. Looks to be a 1/4...

Is it possible to connect a Simrad AP25 control to where the old the Simrad ap20 control head is located. I know they are different connectors that go into the head unit but is there are way to say, use the Simnet (i think it's called) cut end off, go to jumper box then connect to the existing...

Does anyone happen to have a GalleyMaid BBHW-24 Anchor windlass manual? Or can explain how to adjust the clutch. The clutch is slipping ie letting the chain out when I try to set it and same when retrieving it. No, I don't use the windlass to pull boat to anchor, I use boat to pull up to anchor...

Simrad AP20- head Unit My Simrad AP20 head unit quit working. Guess it's the head unit that is busted as it will no longer turn on. Stop working first day crossing over to West End. Does anyone know where to get one, or has one to sell? Or where to get the old head unit fixed repaired, checked...

Morning, After basically having the entire running gear redone replaced, still have the high pitch loud squeak. Shafts trued / unbent, props balanced , new cutlass bearings, shaft logs etc etc. Only thing not replaced were the struts. So we splashed yesterday and I'll be danged.. Starboard...

Broke down and decided to have an Inverter installed. Having the old wet cells replaced. Some reason this boat has 2 wet cells 8d's and 2 AGM 8ds hooked to a wet cell charger. (pretty sure that's not good for the AGM's) Gen starts off the starboard engine bank Installing a 3000 watt xantrex...