Search results

We are northbound on the icw between Brunswick and savanna geogia. Stb engine cylinder not firing and suspect injector or valve problem. Running on one engIne. Can anyOne recommend repair yard or mechanic for CAT 3208t 320 up diesels. Many thanks. John

I broke off the port trim tab and actuator and am looking for a part / model number to order a replacement. They are Bennett tabs. Have spoken with both Bennett and Sams and we have not yet been able to identify the exact tab required. Anyone on the forum with a mid 80's 36' Sedan or Convertible...

A fluid leak caused my port Bennet trim tab to collapse while underway. It looks like it may be bent, and will not move. I am currently on the loop and will be arriving in Fort Myers within the next week. Can anyone recommend a good technician to repair it while I am docked at Legacy Harbour...

Here's a copy of a post in today's AGLCA forum cautioning fellow loopers about passing tows(tugs pushing barges) This past Friday we met a tow named Chippewa on the Tenn-Tom near mile marker 218. The captain, as usual, was very helpful in negotiating a smooth meeting on the "ones". We had a 43...

Departed southern Lake Huron on August 16th heading north, then south on Lake Michigan though Chicago to the Florida Keys. Should be a wonderful thing staying in flip flops for the next ten months rather than putting the boat on the hard for the winter and getting out the boots and gloves. So...

I'm about to change the transmission oil on my twin disc transmissions (Cat 3208). I am unable to read the amount of oil and the oil viscosity on the transmission plates. I believe the oil viscosity is straight 40 weight. Can anyone confirm as indicate likely amount required as well? Thanks. John

In case you haven't seen this one. John NEWS From BoatUS Boat Owners Association of The United States 880 S. Pickett St., Alexandria, VA 22304 BoatUS Press Room at http://www.BoatUS.com/pressroom ( http://smtp.boatus.net/t?r=5&c=1363 .. 50A16& ) FOR IMMEDIATE RELEASE Press Contact: D. Scott...

The factory installed GFI which services my galley and head occassionally trips for no apparent reason. I can't find anything in the wiring so I think its just an age thing. I know these don't last forever, and after 25 years I'd like to replace it. Question: can I just install an off the shelf...

Hi folks. My Hatt has the original 2 battery set up, one for the starboard engine and generator and one for the port engine and house use. On my upcoming loop trip, I'm wondering if my single port engine/house battery will be enough to run my Norcold fridge overnight while at anchor without...

We're leaving in August from the Great Lakes for our loop trip and plan to try our hand at some trolling while travelling. Can anyone suggest a salt water combo that will last a year for a couple of beginners, and modestly priced. Its difficult to get salt water rods up here. We are thinking...

here's a striking tribute to all those fishers lost at sea http://www.youtube.com/watch?v=y8B0mrWIDxw&feature=related

My engine room access panel in my salon floor is quite heavy, awkward to lift out to check my engines, and its a pain to put it somewhere while I head down below. Has anyone tried putting this panel on hinges, with gas assisted struts to help lift/lower and keep it open? Perhaps the bigger boats...

Here I go again showing my lack of knowledge as I figure out the boat .... the attached picture shows a black box with an opaque bottom section located at the stern of my lazarette. I am wondering if this holds hydrolic fluid for my trim tab system, and how I service / maintain it? How to open...

I'm heading to Florida next winter which I am told has more lightning strikes than other areas of the US, and I am wondering if Hatteras built any lightening protection into their boats in the mid 1980's. Forum searches reflect multiple threads where the whole issue of lightning protection is...

A friend of mine is interested in a '88 48' Sportfish being auctioned off by National Liquidators in Ft. Lauderdale. He went down this week and looked at it and the interior need redoing but otherwise seems solid. Priced at $129,900 but thinks it might go for less. Does anyone know this boat /...

My Hatt has factory "grey" in the ER, but I've noticed many of the pics on the HOF show white walls & floor in the ER. I like the white look and its likely very easy to see any leaks, spills etc .. but is it hard to actually keep it that white? Is the ER color it just a matter of preference...

Hi folks. During my great loop trip starting next summer I'll be going through a lot of locks, and while I will have friends with me for part of the adventure I will likely find myself by myself from time to time dealing with going through locks. Anyone had any experience in doing this from a...

Can anyone help me identify the type of transmissions I have in my 86 36' Hatt?. The engines are factory installed Caterpillar 3208 turbos rated at 320 hp. There is no reference in the owner's manuals to the transmissions. Is there a plate somewhere which identifies them, or does someone on the...

Hi folks. Mooring balls are fairly rare in the Great Lakes but on my loop trip next year I suspect I'll find a few of them. I have only anchored out, and never used a mooring ball. I'd appreciate some advice on hooking up to the little devils. Do I need a specific setup, or can I just use a dock...

I suspect this may open a can of worms, but here goes. My freshwater Hatt (Great Lakes) has an epoxy barrier boat with Interlux VC 17 on it. I'm getting the boat ready to do the Great Loop which means changing the bottom paint for one that works in salt water. In talking with Interlux, nothing...