Search results

Hello again, does anyone recognise this genset. Kohler 12.5 kva model 125cc061. I am in desperate need of wiring schematic. Regards, Peter

Hello, I am looking for a wiring diagram for a 12.5 KVA Kohler Genset model 125CC061. Can anyone help please. Regards and Thanks, Pete

Question, on my DD 8V92, the raw water system pumps water through the inter cooler, fuel cooler, heat exchanger, through a pipe with a T fitting, into the shower head . The T fitting allows water out the side through a valve. What is the purpose. Thank you P.

Hi, I am trying to get a contact at Hatteras to see if they have any records for my 1982 46C. there website only appears to be for buying new boats?? Regards, Peter

Hi, I am a long way from my boat. Can anyone here tell me what size belts are used on a twin pully engine alternator for an 8V92ti. Regards, Peter

Hello all, I will be travelling to west Palm beach next week and will be bringing eight fuel injectors from my 8V92. Can someone recommend a good shop to have them serviced. Regards, Peter

Hello, running into a bit of a problem. I live in south east Asia and have a 46C. The generator on the boat got some water in it and seized after a long period of non use. I took it off the boat and dismantled it. Got it all moving again and went looking for gaskets. Its a Kohler 15kva genset...

Ok, here's a tough question, possibly one of you gentlemen can help. I am looking to purchase a couple new turbos for my boat but am running into difficulty identifying what I need. I have contacted three different suppliers and have been offered three different turbos. The turbos I have now...

Hello from Borneo. Well the heat exchanger on my Generator failed and filled the cylinders with water, corroded and now seized. Managed to dismantle it and removed it from boat. Boat on mooring, had to hand carry 500 lb engine onto tender, not for the faint of heart. Looking at an engine...

Can one of you fine people direct me to a company from whom I may purchase a Turbine Housing for a 8926192R TURBOCHARGER TV7101 AR 1.23 8V92TI . I live Asia with no Tech. support. Best Regards, P

Result; a few year ago I bought a '82 46C with 8V92ti (650hp). Over the years I have done a lot of work on the engines, hoping to get as much out of them as I could. I rebuilt the blowers, turbos, intercoolers. pulled the injectors and cleaned , repaired, and replaces as required. and spent...

Hi All, OK this is a very broad question but I need to start some where. I have a 1982 series II 46C HP with DD 8V92ti engines rated at 650 HP and the boat weighs 20 tones with low fuel and water. I believe the props on the boat now are 3 blade 28 x 27 pitch but are in dire need of tuning I am...

Hi, About three weeks ago I was out on the boat and turned on my Garmin chart plotter and it gave me an error code "Error code 2 Radar needs repair" (Garmin GMR18HD about five years old) I searched the internet and finally came onto a site which said that error code 2 is that the Magnetron...

Hello, I am seeking advice. In the effort to get the most out of my old engines, I have preformed a couple complete tune ups. Rebuilt the blowers and turbos, bought a couple exhaust manifolds, and a set of injectors. (No, I did not have the injectors flow checked before installation, this I...

Hi All, I am coming to west Palm beach for the last couple week of August. Can any one tell me where I can get my fuel injectors serviced in that area? I have Detroit Diesel 8V92 TI engines with 9A31 injectors. Also I would like to find a Cruisair place that may be able to help with some old...

Hi, I need some input here. Took the boat out on the weekend, 46C with DD 8V92ti engs. Cruised about four hours at 21 knots, no prob. Slept on boat. Next morning drove about two hours at 14 knots then brought the boat up to 18 knots cruised for about twenty minutes, then right hand engine lost...

Hi all, I have been frequenting this site for over three years now, ever since buying an old boat. Over that time I have got a lot of good information from many of you, so thanks. I live on the other side of the world with no real support except a couple manuals, internet browsing and what I...

Hello all, I am having some trouble with my Kohler Generator 15 KVA model 4JHL-K. Does anyone have a wiring diagram for this unit? I have tried to get one from Kohler but they insist I use my local dealer here in Asia, but they will not reply to my query. The problem is that after the unit has...

Hi all, hopefully one of you is in the know.I have pressed out the old cutless bearings from my struts (46C, 2.5 inch shafts) and the new bearings can be put back in basically by hand, possibly a bit osf tapping with a hammer required. Should there be a closer tolerance fit or even a press fit...

Hi All, I am reconditioning the stuffing boxes on my 1982 46C with 2 1/2 inch propeller shafts. The old shaft log hoses where not correct, (thin walled hydraulic hose 8 inches long) I have purchased the correct heavy walled hose which is sold in 12" lengths. Question; what length should the...