Search results

Getting settled in Jacksonville, Florida and need to get established with a new set of vendors. I would appreciate any recommendations on Detroit Diesel Mechanic (preferably w/DDEC experience), Electrician, HVAC, Diver, Wash/Detailers, etc, etc.. in the area. And maybe more importantly, the...

It appears I many need to replace my water tank sending units. Does anyone have a better diagram or instructions on how to most effective replace the water tank sending unit on a mid 90's Hatt. Looking through my Hatteras engineering drawings, this is the only digram I have. I'm hoping I can...

Replaced the 20KW Onan with a new Northern Lights 20KW (outstanding upgrade for the Bahamas on the hook!). Was getting ready to do some routine maintenance and can't find any zinc/anodes on the unit. I went through the Owners Manual, Maintenance Manual, Spare Parts Manual and could not find...

After 28 years of good service the water heater tank has cracked and is starting to drip and needs to be replaced. It is a AO Smith glass lined 19 gallon, 2500watt, 220volt unit. Looking for options, replace with same or is there a better option?

For the past 12 years we have relied on the Galley Maid MR24-10 pump (24v, 10GPM) to supply the boat with fresh water. For the most part, it has been one of the most reliable pieces of equipment onboard. This past May we arrived at the Highbourne Cay, Exumas anchorage, watched an unbelievable...

On this last trip we had a 24K BTU scroll compressor give up its life in the engine room. This is a Split System. It has been suggested, I have 3 options at this time given the existing system utilizes R22 Blend refrigerant. 1) Replace with a NEW MarineAire/Dometic 24K BTU system, that...

Is there a better Perko 493 series strainer basket replacement (Perko # 049300899D)? I'm tired of replacing the SS baskets every couple of years. It appears only to be an issue with the AC strainers due to volume of water flow. Being in FL, AC's run a lot! The baskets are cheaply made, bad...

I have an old Potter & Brumfield (P&B) relay that is no longer in production. I would like to replace with more readily available 5 pin Bosch relay. I'm not really familiar with the P&B relays, other than they where high quality. What would be the proper pin conversion from the P&B to Bosch...

Does anyone have a PDF of the install instructions for Marquipt Step Plates. We have a set installed. We are attempting to remove but there appears to be something preventing removal other than the 6 visible screws. We want to ensure we are not missing any hidden screws or if someone possibly...

It is just about time to replace my AGM's. Over the years I have purchased from Royal Batteries. Was curious if there are any other distributors I should consider?? https://www.royalbattery.com/

I few years back, I took the 4 solenoids apart for the Wesmar Bow Thruster (13hp, 24volt) when the solenoids where getting sticky. Cleaned the four solenoid internal coils, springs, flipped the washers and the thruster was back to working - good as new. The solenoids are getting "sticky"...

Was on the https://www.hatterasyachts.com/ website today and noticed the only boats being advertised are Sportfish models. The Motor Yachts appear to be no more…. Does anyone have any insights?

Can anyone confirm what grade of chain this is? I have not been able to find any good cross reference to what appears to be “AS” stamped on the sides of each link. Thoughts?

Have RPM Diesel scheduled for the Dec-06, to address an issue on one of 8v92’s . Curious if there is anyone else in the Palm Beach area worth calling?

I have 227 volt at the meter coming in at the boat but only 106 volt at the AC outlets? My Air Conditioners do not like this low voltage and the AC raw water pump died last night. With 227 volts coming in shouldn’t I be getting around 113.5 volts at the outlets, given the 227?

During a refit, the two Central Vac units, hose, & attachments where removed as we never used them. Free to good home for cost of shipping. I would like to see them repurposed; otherwise, they will be recycled. Below is a pic of the 2 head units.

Replaced my Onan MDL4 20KW GenSet and no longer have a need for these spares. Yours for some beer money ($50) + shipping. Includes Oil Filter, Fuel Filter, Impeller and belt.

We have replaced some carpet with Amtico flooring. The Carpet was hiding some hatches that now need to be trimmed. We have the aluminum T-BAR to trim out the hatches. My question, does anyone have any tips/tricks to make the radius bends preventing the inner part of the T-Bar from wrinkling...

I'm tired of lugging around an external BucBooster for docks that only have 208v. I was looking for alternative and came across this today. It appears to be the next generation Charles Iso-Boost, plus it has some intelligence built in to deal with low/high level line volt conditions, which...

Well maintained Onan MDL4 20KW generator with Sound Shield. This unit came out of our 1994 Hatteras during recent updates to new 4-stroke GenSet. In good working order when removed and have all oil analysis reports since 2009. Will upload pictures in the next couple of days. Send me a PM if...