Search results

I have zero screens for my portlights and having no luck finding replacements. Sams lists them but shows none in stock at $25 a pop so it would cost me $350 I searched online for them with no luck. so I figured I could just cut some screen to fit and glue down to the lip the screens would lay...

I have these for a pair of 454’s if you think you can use let me know. They do need to be mounted horizontally. From what I see in your pics I can’t see anything real bad. Maybe it backfired thru the carb?

What is a good product to use on my walls? I get the mildew on them and wondered what folks here use to clean them. I do a monthly wipe down in season so the mildew isn’t bad, I have a can of lemon Pledge plus a few other wood cleaners. I used some very diluted bleach and also white vinegar...

Maybe those who complained need a 30 lockdown. It’s friggin pictures!!

I’m thinking about adding a bow thruster but not sure if the costs etc would make it worthwhile. there are elect and hydraulic units and quite a few manufacturers all have pros and cons to each. I like the hydraulic units without needing more batteries etc etc but the battery units have been...

Sad day for many. I hate watching the shows but I just have to. God Bless

My fridge is on its last leg and looking for a replacement. Orig size is roughly 64”H x 33W x 25D with doors off. Problem is my ac panel at the top of stairs, the trim sticks out 1 3/4” so I have only 23 1/2” of width, if I can remove it easily I’ll have 25 1/4” of width. All I see is two...

I have just replaced my aging 8V batteries and now I’m ready to replace the original lamarche unit. I haven’t found many options other than analytics which Metama had mentioned and currently has on his 53My. the analytics has a 4 week build time and priced at around $1,200. They also specify...

I can't find the receipt or part# for my transom zinc. I know it was over$100 at old marina and boat zinc . com doesn't show what I think it looked like.

Just got my non renewal notice from Pantaenius. Who should I go with ??

I'm looking for some info. I want to setup a oil change system. I would like to plumb it from the oil pan but don't know what size etc connections the oil pan takes. I will be plumbing it for both 871's and would like to have it drain thru the air inlet to a dockside 5gal buckets so I'm not...

Any interest ?? FREE. Does not come with faucet just the sink. Perfect condition.

My GM forward head won't fill the bowl, drains ok but bowl,won't fill and no flush water. Haven't used this season and worked fine last season.

Just did a full re plumbed my freshwater sys and while doing that I noticed my 20gal water heater needs to be replaced due to leaks. It took a lot to finally remove the 22" x22" tank thru my 17.5" doorway. It is wired to a double breaker so I assume it's 220v ac. I cannot find anyone that...

I did a horrible job winterizing my dockside freshwater system and now I'm paying the price. I have chased multiple cold and hot water leaks and made temp repairs along the way and have hit a dead end. The pipes that run from the washer to the forward head go under the floor and I can reach them...

""...............

I have two marine mufflers that have been in my attic for 15yrs. They are new never used made in 2001. There are two 4" inlets and one 5" outlet on each. Make offer.

I would like to install a priming pump for my twin 8v71 ti's. I lost prime last year and couldn't get one side to fire off. I ended up having a mobile tech prime and run that motor. For the price I paid I figure I could install one tied to both motors. I searched here and found some info. I...

Looking for some help. I slip in salt water and on my previous boat I used interlux ACT ablative and wasn't impressed especially if the boat sat for a few weeks I would have shag carpet in no time. My boat now will spend most time tied up, going out once or twice a month during my summer season...

I need to replace the wheels/casters and cannot get ANY movement. What's the trick? I have them soaking in WD, it's low 30's here so I'm trying to shake off some cabin fever. I also need to replace some bolts that hold the steps to the side rails. I had one step that was missing both top side...