Search results

While arch is off, doing the deck. Just finished filling all the holes and fairing some. Now to replace the divinny cell that got wet and delaminated in that one spot

Arch all sandblasted Welder due out Monday to fill in / patch the 100 holes that have been put into this arch Also will be fixing some stress cracks. Still have not decided what to do, paint or powder coat

Cockpit shade all done, and also added some shade up front. Quick take down / put up in 5 mins. Use it for when too sunny and wife wants to sit on the bow. (not pretty, but it works :) )

90% of the old nasty non-skid is now remove. Have to reglass the 100 holes that in the deck - of course after it all drys out. Lucky it was some dense closed cell foam not not wood up there. looks to have been leaking for a long time. Going to prime and paint using Alexseal - roll and tip

Are these Aluminium I-Beams on Dingy deck Factory or installed at some other point in time They seem a little over kill for a dingy, unless at one time there was something else installed up here they run the entire length and then the side pieces at the aft are welded to the long pieces. Then...

Kinda of out of order but while removing arch also having new screens / back enclosure and cockpit shade installed. Should have waited for the arch to be removed before canvas guy started but oh well. Also, got a new 58' Hatteras as a new neighbor last month. Has a nice jet boat for a dingy

Divit should be close enough to move it?

well after much debate and grinding. Decided to remove the Arch Only 4 2 1/2" 1/2 bolts on each side hold it down. I loosened one side to test the bolts and they came out easy. Any Idea what arch would weigh? going to try and get it down with my davit I Removed all the mounted stuff, and the...

Oh and here's 2 night time pics, one with patio lights on one with the only lights from outside of patio on and the ambient light from inside the house. This is with IR off, and only using their light finder software Will be getting a couple for the boat, due to easy setup etc.

Any of you experts know what model Cat pump this is? I contacted SeaRecovery and they want 240 for O-Rings, and 570 for valve o-ring kit. I heard of some markups but that is crazy. Pretty sure I can just get a new pump for around 1500.00 Of course it's been re-branded by SeaRecovery so I can...

Anyone know if there is a guide on how to measure for the marquipt sea stairs not sure if I need a 7 or 8 step. I don't see any guides or install directions on the marquipt site thanks or any advice on how to tell :)

It was easy. Even a noob like me did it :) I just flushed / acid back washed all 4 of mine last weekend. 1" line from seacock, and 5/8" going to a manifold for the discharge. built a manifold with the 4 5/8" barbs and the 1 1" barb purchase a rule 3700 24 volt bildge pump (yea way to big) but...

Now if I could figure out how to get the 3 other dogs onboard 1 1/2 year old Shepard Soon to began learning how to get on off boat / tender (I hope) 13 year old Male and 12 year old female (these 2 are too old to be hoping around the boat)

Navigator and Look-out :)

Looks like I spoke to soon. Looking at the top of my holding tank, what I thought was a sending unit is just some copper vent tube, hooked to a 1/4" plastic tubing then runs through a bulkhead and ends up over the shower sump not sure where the sending unit is. Only one holding tank that 3...

Hi All, have 3 vacuflush toilets plumbed into a center line holding tank. Appox 85 gals give or take. Just realized yesterday that the red lights in the heads are not working . they are supposed to warn on 3/4 tank full. Question is, how do I test the sender unit on the tank. Looks to be a 1/4...

Is it possible to connect a Simrad AP25 control to where the old the Simrad ap20 control head is located. I know they are different connectors that go into the head unit but is there are way to say, use the Simnet (i think it's called) cut end off, go to jumper box then connect to the existing...

Does anyone happen to have a GalleyMaid BBHW-24 Anchor windlass manual? Or can explain how to adjust the clutch. The clutch is slipping ie letting the chain out when I try to set it and same when retrieving it. No, I don't use the windlass to pull boat to anchor, I use boat to pull up to anchor...