Search results

trying to find dimensions of aftermarket engine vents for a 46. I was given a set some guy had floating around in his shop, but they are 8 ft. long and 22 inches high at the fwd. end. He said they were from a Hatteras

4/0 cables for main engines need replacing-insulation cracked/peeling, also relocating battery boxes. I have always used crimp connex terminals with heat shrink in the past, though never worked with cable this large. The terminals on the factory cables appear to be soldered, and in fact when...

Going to replace the original copper fuel lines which are 5/8 o.d., would this be 1/2 i.d. ? these are for my 1979 46 conv. with 871 ti's. Will be using conventional shields fuel hose. What is the proper size to use?

the teak has cracked/split. Anyone have any success or suggestions for alternate material? Starboard would be easy but not sure about success of caulk adhering to starboard. Is there any source to get these with the bevel already cut? Thanks

Model75000000 16 . seperate fridge and freezer doors, excellent condition-$500.00.

This boat was on the bow of the 46 convertible I purchased. For sale is a 1989 11 ft. 6 inch whaler with a 2005 30 hp yamaha 2 stroke. Boat is in very good condition, engine looks brand new. Carbs have been removed and cleaned, installing new impeller this weekend. Electric start, wheel...

Just inherited an 2005 Avon RIB. It is structurally sound but stained with mold/mildew. This thing sat around for a year or more covered in leaves, debris, etc.. Any suggestions for cleaning/restoring pontoon material?

need a solenoid for horn actuator, have a compressor and tank which are good,current solenoid inop. Also need (2) for my atlantis freedom heads which I am converting to freshwater flush. Currently both have the seawater intake pump, but removing those and wanting to add a solenoid to my house...

Anybody know the recommended procedure for checking oil level on allison m20's? Running, not running, warm, cold, etc...

Installed freshly rebuilt sea water pumps on both engines past weekend. Old suction hose was 2 7/8, and a caliper on all fittings agrees. Tryed to install new 2 7/8 shieldsflex II hose on the pump suction side fitting, but could not get hose tight on pump fitting, all the way up to snapping...

sea water pump housings to be specific. Have them completely stripped and looking for something to remove grease, grime, green corrosion, etc.. Thought I saw somebody reference TSP in a previous post-will this do it? Other suggestions?

1979 46 cnv with 871ti's. Raw water exits heat exch. thru a 2" hose which connects to a bronze "t" which drops down to two 1 1/2" hoses which go to the shower heads on exh. elbow. Problem is the "T", which is a one piece bronze assy. is in need of replacing. DD says it is not their part. My only...

since boat is out of water and rudder table/upper bearing support was looking pretty tired I removed the whole mess( it was 3/4 plywood) My thoughts were too replace bearing support with some aluminum c-channel, probably 4" width. In addition to the two rudder bearing supports, I will have to...

wanting to install a transducer before I splash boat. was hoping could install a transducer that I could "fit" to any system, since dont know what I will install. Being told that transducers are specific to manufacturers, even though they're all made by airmar, something about different diodes...

1979 46 cnv. There is a diaphragm pump( belt driven motor mounted on top of pump body, approx. 4 x 6 inches) under the lower bunk in the v-berth.One hose is connected to holding tank and the other hose is hanging adrift in the anchor locker. Cant figure this one out.

Pumps are mounted to bell housing and sit above allison gears. Look to be six bolts securing pump to bell housing. Is it as easy as removing six bolts? I am thinking there is a flywheel driven gear on the end of pump shaft.

Looking for manuals for 871TI. Would'nt hurt to have manual for allison gear also. Or is there an easier way too access info?

have spare 2 piece shaft from 1979 46 cnv. 8ft. plus 4ft. with muff coupling. Also have muff coupling from other shaft plus 4ft. stub

want to remove a few unnecesarrary ducers from hull. Procedure for filling in holes? Looking for detailed instructions for do it yourself

this is the dink sitting on my foredeck. Includes chocks and custom ss. spreader bar/hoist bracket for the marquipt(which I'm keeping). 30 hp. yamaha on back, steering wheel and single lever control at helm