Search results

I am going to be removing the three-drawer end table and the flip-top bar/cabinet that holds the ice maker. They are the originals and in decent shape. Stamped on the back from Hatteras stating were used for 42, 43, and 46's. Located south fl.

have a MH 20L gear that came with RTO 871TI. Very clean, low hours.

for sale craigs list in Marco. This was taken off of new boat.

Craigs list, 1975 45 for 65,000. Goodland Florida, around the corner from me in Marco. Have not seen boat, but sounds like a good deal.

looking for gchart for south florida, needs to include Naples area and the keys. This is an original unit on board that will be my 'backup'. Have g chart gus144xl for sale or trade.

Shopping around for anchor swivel, west has 'KONG' brand. Anyone have any experience with these? I believe they are made in Italy. Have also seen swivels that pivot, is this a better design?

Went to Home Depot today to purchase phosphuric acid based product(driveway/concrete cleaner, etc) for H/E flush. Could not find any. None of HD. products I found were phosph. acid based. Where else can I find this or is another product suitable for the recirculating raw water flush?

I am going to resurrect this old thread. Tryed everything on old Avon; every cleaning agent, including bleach,simple green, acetone, brushes, 3M scrubbies. sandpaper, etc.. So went to Avon dealer to inquire about painting tubes. He explained what I had was mold/mildew on the surface. Tubes...

heads are off and liners/pistons are out. Liners heavy glaze, some rust staining. Two front liners on either bank rust/minor pitting from leaking injector tubes. Engine deck stamped with #1 adjacent to each cylinder from factory, yet liners I removed have stamp/id. below intake ports, which...

Dont know if I have the correct name, but this is the assy. which connects both wet exhaust banks too the muffler tube on each of my 871TI's. These measure approx. 6 " on each downtube and 10-11" on horizontal collector(eyeball measure). Originals on my 46 conv. are stainless, but all pitted and...

Pros and cons of coolant versus oil type heaters. What is recommended watts for each? Thanks

new par jabsco 24v blower 34739-0020, $100.00 sealand 24v vacuum generator VG-24v, tank and motor, good used, $300.00 sealand 24v TW vac pump, new $300.00 sealand tank with float switch, commonly used for bait/livewell, 24v, new $100.00 mercury quicksilver thunderbolt IV ignition module 15899A...

getting rid of original 871TI air filter/intake cans(not sure what you call them). Total of four.

while changing out fresh water pump on 871TI had to remove thermostat housing and noticed thermostat is a 160 degree. Pulled left bank housing and that is also 160. Would not a 180 degree be appropriate? Have never verifyed actual running temp., but gauge does indicate 160-170 range. Boat is a...

1979 46 conv., has Fuller Brush Co. portlights. I need several screen inserts and numerous wing nut/eye bolt assys. which hold the cover closed. Anybody have a good source for these? Thanks

Pump on stbd engine leaking from weep hole. My thoughts are to get a new/rebuilt pump too replace it and rebuild the current as a spare. My 871TI engines rotate opposite, so are pumps interchangeable LH too RH rotation( would one pump serve as spare for either engine)? Also looking for new or...

1979 46 conv.-new one piece shafts and dripless seals, new cutlass bearings, tuned and balanced props. Both port and stbd sings when placed in gear. Continues too 1200-1300 rpm at which point engine noise dominates. Have placed one then the other in gear-either produces the same noise. Noise...

I need the control head for this unit. Both screens on the unit are burned out from the sun, system works though.

1979 46 conv. Looking for the bulbs that sit behind the red, round screw in covers on my main ac-dc panel. These indicate shore power, generator, water heater, batt. charger, etc.. Thanks!

Looking to install new vhf in flybridge overhead electronics box. Considering the icom 504/604 and uniden 525/625 are . Leaning towards uniden because of price, will also be using remote mike for salon and uniden has a wireless, so zero install woes. Any feedback greatly appreciated.