Search results

Danforth 60 H High Tensile Anchor SOLD! Sold sold sold

Tip was pretty corroded. Instead I replaced the wire with an alligator clip soldered on and just clipped it on the stub. Need to back up and clean up that rig-job. Here are pictures of the plug: The manual indicates 333-0106 for 12 volt boat. Help appreciated at a market-fair price. GT

Cummins Onan says it's discontinued (12 volt version) and offers no xfer. Need a new old stock version, or a current cross reference to a champion or NGK or similar. this is for a Onan 7.5 MDJE.

I have some antifreeze coolant collecting in my engine pan below the ONAN MDJE 7.5. She will run for 4 or 5 hours and then shut down for overheat. We add about 3 cups of antifreeze to the tank, and away she goes. I have checked all the hoses on both sides of the water system and I cannot find...

One blade with slight damage from shallow encounter with mud bottom. See pictures. Make offer for the pair or message me with questions. GT Correction to listing title: Should read "C399", not C300.

Used on Bertram 42 Flybridge, 42,000 lb. boat. Good condition. Asking $500. Anchor is in Dallas, TX. Private message me with questions. GT.

Our ONAN 7.5 MDJE suddenly started blowing black smoke and spewing diesel fuel into the water yesterday. It continued to run, but we shut it down within 10 seconds. Initial concerns are possibly one cylinder dead-heading, or other serious failure. This is a very old unit leaving us the...

I have a friend of a friend who says he was just charged $85K to clear through the Panama Canal. We are trying to back into the math. Can someone give me the short and simple on how to calculate your cost to clear the panama canal? Thanks, GT

Does anyone have specs on the amp draw for the 120 volt Euro Kera forceio 2 burner ceramic cooktop? We are tripping breakers and the panel amp guage is broken. Thought someone might have the wattage and amp rating handy...

THe AC panel ammeter has failed on my 120 panel. I have 30 amp service and further inspection on the inside of the AC cabinet shows a large sand colored donut that appears to be part of the gauge, apparently around the main power source wires from the Shorepower inlet to measure amperage...

I added the mechanical oil pressure gauge on the starboard engine and found that the engine runs 39 lbs at 1200 RPM and up to 42 lbs at 1600 rpm, and then drops to 9.5 lbs when engine slowed quickly to neutral after hot. How is that in comparison to expected? Normal idle oil pressure after hot...

with picture.

Thanks for the direction on the pressure block, Genesis. I have attached picture. I was thinking that end plug could come out and go in with a NPT hose and guage there? Please see attached picture.

We need an aftermarket -multi fit bow pulpit for mounting across uneven surfaces on the bow of the Bertram. Open to any adaptable solution, but will need to work with 45 lb claw Manson Supreme anchor. Don't want the cost of integrated handrail. Just trying to solve the problem logically. Many...

Over the last 6 months, the minimum idle to avoid setting off the low oil pressure alarm has gone up for my starboard 671 turbo. It was originally about 680, but is now up to almost 800. This engine shows about 40 lbs at cruise and right under 20 on electronic guages (no mechanicals installed)...

And here are the photos of the order of installation. In the first pic the allen wrench represents the body of the pump. Everything left is on the impeller side of the pump, everything right is in the bore. Second photo is the assembly of the seal parts.

Here is a photo of Allison M20 Gear box. I add oil at the breather. If you notice the gear selection lever at top, there are two brass plugs in the top of the selection lever unit. the bright brass cap is low pressure and the lower one (less visible) is high pressure. This forum recommended...

I have the rebuild kit for the raw water pump on my Onan 7.5 MDJE. The shaft sheared in half so disassembly was not clean. Now I am not clear how the two part seal and spring go back. If I understand correctly, the rubber and white portion of the two part seal gets dropped into the deep end of...

Re: Exhaust Manifold- ONAN 7.5 MDJE 3CR 2268 AC- Saga continues The nipple fell off in my hands when I got ready to drive it off the threads in the manifold, rusted through. the manifold is messy on the end. depending on cost of a used unit, finding a machine shop to tap, or cut it to...

I need an Exhaust manifold for my Diesel ONAN MDJE. The Cummins Diesel part number is 154-2122, which superseded the original part number 154-1058 for the heat-exhanger version of the manifold. The end where the nipple and Exhaust elbow attach is rusted out. The inner threads where the 1...