Search results

Guys: I am trying to help my brother get a DC he is looking at Carvers etc. I have found a gorgeous 38DC in freshwater. Can anybody give me an idea of the selling prices for a nice 38DC 1974? They are asking $79. Sea Eric? Thanks. DC

Hello: I have 3 chairs like the one in the pic. They are located in the Detroit area. I am open to any offers for 1, 2 or all of them. Maybe we can find a way to get them to the Hatteras Owners School. Thanks. DC

I have recently upgraded the galley dinette table on our 53EDMY (1985 Model). If anyone needs a table in original condition please let me know. Free to a good home, located Metro Detroit area. DC

I am still in need of the R-100 control for my bridge. Please let me know if you are aware of one for sale. Thanks. DC

FLEXSTEEL Couch from Bradd and Hall; Elkhart, IN

After Stormy's problem with the heads, then the pictures from Bohemia Bay and the loss of John & Rosemary's boat; it is hard not to lament about boat problems. Here in the Great Lakes basin we are having our own problem. Ice jams and "dams" in the St. Clair River between Port Huron and Algonac...

Hello: Does anyone know the proper specification for the bell housing on 6V-92TA engines with Allison M20 gears? Is it "SAE #1" for example. If changing to Twin Disc gears (dry flywheel versus wet) can you use the existing bell housing? Any information or source for info. would be...

Hello: How do you tell if the Ace motor mounts have collapsed or failed, or if only an alignement is needed? I have 6V-92's on the Covington style 3 point (2 rear 1 front) mounts. I definitley have an alignment issue, but it may have been here for a while and gone "unnoticed". The mounts...

Guys: Does anyone have the measurement for the LOA of the shafts in 53MYs? I am needing this information to do some engineering calculations regarding shaft materials. Any information would be great. Should consider quill shaft length plus "main shaft" including coupler as one dimension...

Hello: I need one of the "caps" that screws into the "shot gun shell" type fuse holders on my 53EDHMY. In oder to buy on you need to buy the whole assembly. PM me here if you can help me. Thanks. DC

This is a 1985 vintage Datamarine sumlog head which was working when removed from our 1985 53ED. $15.00 plus shipping. PM me for a photo, sender not included. DC

This is a "vertical" layout. Removed from our 43DC when I switched it to SMX. The temperature probe was "cut" by the technician that did the work. $15.00 plus shipping. PM me for a photo as I do not know how to post one here. DC

Hi Guys: Karl probably has a quick answer for this. Our port engine starts much better with the throttle "cracked" a little. That means when the engine fires up it is turning 1000RPM's or so, you can immediately slow it down to idle with no stalling or stumbling. Filters are good etc...

Hi Guys: I have a Dell laptop I want to mount on the "dash" in the pilothouse of our 53ED. I want a clean looking set up that will hold it in place. Nothing big or obtrusive. Anyone have any thoughts/suggestions? Thanks in advance. DC

Hello: We have completed the installation of the thruster tube on our 53EDH. I have a piece of tube from WESMAR that is long enough for a 53 or larger HATT. It is the 12 inch diameter tube, now cut on an angle on one end 41" on the short (bottom) side and 51" on the long (top) side. I am...

I have: 1) DATAMARINE International Offshore Depthsounder Head Circa 1985 removed from my boat this year. $35 plus shipping (I do not have the sensor available). 2) DATAMARINE Navigator Speed/Sum Log Model 3200 Head Circa 1985 removed from my boat this year. $35 plus shipping (I do not...

Hello: I am installing WESMAR stabilizers on our boat, the power supply is 12V 8amp requirement on a 10amp breaker. My question is I want to run the power supply wire from my 12V supply on the bridge, the length of the wire will be approximately 35 ft, will 12AWG be heavy enough for this...

I will be having my 53ED's bottom "stripped" using a media blast. Then we will do a complete blister repair and Interlux bottom system. I was wondering if anyone has recently completed a similar job and if so how much for stripping? Always trying to keep things "competitive" with quality...

I have changed my primary and secondary filters on my 6V-92's to spin on's so I have 2 sets of canisters. I also have the following elements: (3) Baldwin PF-590 (RACOR 2020SM) (1) Baldwin PF 902 (DDC #5574508) (1) AC TP540X (DDC #5574508) (1) AC Sock...

I had to replace our Galley Maid pump last week. After the new pump was installed, the breaker pops when there is a load on the motor. I conditioned the stator as I have been trained by GM. Is there a chance that the breaker is "bad"? How do I test the breaker? Thanks. DC