Recent content by av8torrich

All:I have my 39SX up on the hard getting a ton of work done in Norfolk, VA. My door has been giving me some problems (jams), and leaks a little, when water is sprayed right on it. The folks at the boat yard have thrown in the towel, and are telling me I need Hatteras to repair this issue. Does...

My vessel currently has a Furuno 1831 Display (CRT Type) installed my vessel. I am in need of a newer, smaller, slimmer profile display for the RADAR. Was there a more modern version of this display made which would work with my existing RADAR hardware?

2014 YAMAHA 6HP Outboard Four Stroke with 3 US Gallon Yamaha Fuel Tank - $1,400.00 Description: This motor has approximately 10 hour on it since break in. It was bought new at TriState Marine in Aug of 2014. The warranty expires through Yamaha in 8/05/2019 with the extended service...

VDO Temp Gauge Question All: After having a pretty extensive amount of engine work done on my boat, my Port VDO Temp Gauge is showing full scale deflection upon turning the key to the ACC position for this motor. My mechanic then switched the connection to the from port to starboard side, and...

Need Help Identifying Rocket Launcher on 39SX All: The attachment came off a 1998 (last one ever built) 39SX. I have asked a few guys around the marina who they thought made this table. One person simply did not know, and the other two thought it was a Relase Marine product. At the Miami...

Hello All: Starting towards the end of summer I had noticed a significant amount of white smoke coming from both motors. The smoke typically would subside substantially as the engine warmed, but did not disappear until a load was placed on the motor's. After further investigation, I have...

Hello: This weekend the Sharp convection microwave oven in my vessel stopped working. This is the original oven which came with the vessel when new. Based on how it failed, I suspect it is a power supply problem. The question is, has anyone opened one of these up? If so, was there a fuse...

All: I have been looking at some schematics for the Morse MT-3. For the life of me, I can find any component which controls friction of the throttle. I have a port throttle contol, which likes to creep back towards idle. Can somone point me in the right direction? If there is such an...

All: My boat has Three Ultra Safety Systems UPS-02-12V Float Bilge Pump Switches. These switches were installed when the vessel was built. All of them are showing signs of problems, and need to be replaced. I have noticed Rule makes an automatic pump, which has the appropriate GPH and Current...

Wondering if anyone has a SPD-6540 Lift Strut which they may be willing to part with. These struts were custom made for Hatteras by SPD. The strut is rated at 200lbs and is 23" fully extended. I did call Sam's, and they have a 23.5" Strut rated for 193lbs. I may chose to try this strut should I...

All: i was looking for some parts on ebay today and ran across this add. I have no relation to the seller, but live very close to the vessel should somone want me to take a look at it...

Hello All: Does anyone see a real problem with using the onboard oil pump for filling the oil on a DD 671? I had a DD mechanic tell me that one should always fill from the top by hand. I understand some of the old oil residue will still be in the lines from removal, but with a good filter...

Hello All: I have for sale a set of 5-Blade Rolla Nibral 32X49 which are deigned to fit on a 2.25" shaft. One is in perfect condition, and the other has some minor pitting. I have consulted my local prop shop, and they claim the pitting will cause virtually no difference in performance, and...

Custom Mirror Fabricator in Southern Maryland, DC, or Hampton Roads? All: The mirror located on the forward most interior bulkhead of my boat cracked over the winter. I have called Sam's and they were helpful in identifying the material the mirror is made from. I would like to have new one...

All: I have had this issue for some time, but the problem has gotten significantly worse over the winter. My sliding door which allow entry into the cabin is sticking. Based on how it feels at some points along the track, I think there is some sort of pheumatic assist. I am wondering if...