I have a damaged rub rail, some may call it a spray rail. Never trust guest, even other skippers, to handle fender duties. The forward hardware, likely 4, are buried behind the chest of drawers and behind the muffler. I can cut it off, but still need to reinstall.
Any suggestions?
'73 58 YF, athwart ship queen.
Thanks
Welcome to the Hatteras Owners Forum & Gallery. Sign Up or Login
+ Reply to Thread
Results 1 to 10 of 18
-
11-29-2020 10:46 AM #1Senior Member
- Join Date
- Apr 2008
- Posts
- 2,003
Damager rub rail aft starboard side
GLORY Hull # 365
Northport, NY
-
11-29-2020 10:59 AM #2Senior Member
- Join Date
- Apr 2008
- Posts
- 494
Re: Damager rub rail aft starboard side
You can't put full blame on the person(s) doing fender work. It sounds like the helmsman may have momentarily lost control of the boat.
Those fasteners are almost impossible to reach and are most likely corroded after 47 years. Find someone small and skinny.Last edited by kelpy; 11-29-2020 at 11:02 AM.
-
Re: Damager rub rail aft starboard side
Hello, have you removed the the stainless trim yet? When I had mine off I found that it was held on with nuts sitting in counterbores. If yours is the same you may get lucky and be able to get it off with some gentle prying once the nuts are removed.
Good luck.
Walt Hoover
-
11-30-2020 09:22 AM #4Senior Member
- Join Date
- Jan 2006
- Posts
- 822
Re: Damager rub rail aft starboard side
After the stainless trim is removed you may be able to scarf a section in and not have to unbolt the entire rail. You may have to chisel the damaged section off around the fasteners then cut the fasteners. It’s not a job that you want to attempt while the boat is in the water. I have no opinion about responsibility for the damage.
-
11-30-2020 09:44 AM #5Senior Member
- Join Date
- Jun 2018
- Posts
- 1,069
Re: Damager rub rail aft starboard side
What is the rail around the top edge of the deck called? I thought that was the rub rail.
Prometheus
1978 53' MY Hull #529
Viera, FL
-
Re: Damager rub rail aft starboard side
I think it is. But there is also stainless molding on the quarter-fenders, which are those rails at the back of the boat, down near the waterline, and I've heard those called rubrails, too.
-
Re: Damager rub rail aft starboard side
My rub rail, a stainless steel rail that goes all the way forward to aft at the widest point high up the hull, was held on by screws into the fiberglass. The quarter fenders stick out at the aft waterline to provide a base for a lower stainless rub rail where the hull is more narrow at the waterline than above, so the high and low rub rails are roughly equal distance from a seawall or lock wall. My quarter fenders were held on by nuts on a bolt which were accessed by removing the stainless rail on top of the wood fenders. The stainless rail was held on by large wood screws.
-
11-30-2020 12:44 PM #8Senior Member
- Join Date
- Apr 2008
- Posts
- 2,003
-
12-01-2020 08:24 PM #9Senior Member
- Join Date
- Apr 2008
- Posts
- 2,003
Re: Damager rub rail aft starboard side
Well the rub rail I s off, 5 3/8 carrige bolts. Likely going fill the front holes and redrill.
Next, get to work reproducing the rub rail, some 12' long.
Thanks for the suggestion.GLORY Hull # 365
Northport, NY
-
Re: Damager rub rail aft starboard side
Did it come off reasonably easily or did you have to resort to cutting?
Walt Hoover