Sky, as I recall his exhausts are now through the sides of the hull in the engine room and not through the transom.
Welcome to the Hatteras Owners Forum & Gallery. Sign Up or Login
+ Reply to Thread
Results 321 to 330 of 1855
Thread: 1969 Chris Craft Roamer 46 refit
-
Re: 1969 Chris Craft Roamer 46 refit
-
-
02-23-2015 07:30 AM #323Senior Member
- Join Date
- Nov 2008
- Posts
- 1,677
Re: 1969 Chris Craft Roamer 46 refit
Exactly. The aluminum tubes were rotten, and that was after only 15 years and 800hrs of use. They also took up lots of room in the aft cabin. So I opted for side exhaust. I'll use the holes that remain in the aft ER bulkhead as a wire and water line chase.
-
02-26-2015 09:23 AM #324Senior Member
- Join Date
- Nov 2008
- Posts
- 1,677
Re: 1969 Chris Craft Roamer 46 refit
It's nice to be back into full stride on my Roamer project. Granted, since I can only work weekends and I waste two hours of every working day driving to and from the boatyard, full stride isn't as fast as I'd like. But still, progress is happening and parts that have been in the works for a while are finally coming together.
1969 Chris Craft Roamer 46 Refit: Installing Aft Stateroom Wall I
Cheers,
Q
-
Re: 1969 Chris Craft Roamer 46 refit
Very nicely done! what do you use to fill the pocket screw holes? Do you put a wood plug in there and cut it off?
-
02-27-2015 08:27 AM #326Senior Member
- Join Date
- Nov 2008
- Posts
- 1,677
Re: 1969 Chris Craft Roamer 46 refit
I noted in the article that, since they're almost completely out of sight, I haven't decided whether to just coat the pocket holes with epoxy to seal the grain or do something else. I could fill them with wood flour-thickened epoxy or, if I want to get fancy, buy some 3/8 dowel and make plugs. You can buy bags of them, but I haven't found any in mahogany. I could also buy a pocket hole plug cutter and make them from scrap pieces. There are lots of options...too many, in fact.
Great...now you've got me thinking about what to do. aarrgh!
-
02-27-2015 08:55 AM #327
Re: 1969 Chris Craft Roamer 46 refit
How about a very thin strip of mahogany just tall enough to cover the pocket holes, glued and/or pin-nailed to the bottom of the panel. Sort of like a very thin baseboard.
Searching...
Daytona Beach, FL
-
02-28-2015 06:56 AM #328Senior Member
- Join Date
- Nov 2008
- Posts
- 1,677
Re: 1969 Chris Craft Roamer 46 refit
I suppose that would work, too, though I'd probably still use epoxy to seal the grain in the pockets themselves.
-
Re: 1969 Chris Craft Roamer 46 refit
Looks great! I think keeping anything that needs access later on that should be removable not to screw in permanent with nails & glue. We had that in the master head sink had to replace the faucet it was a bear of a job.
-
03-01-2015 08:45 AM #330Senior Member
- Join Date
- Nov 2008
- Posts
- 1,677
Re: 1969 Chris Craft Roamer 46 refit
No doubt, maintenance access is something to keep in mind. But the work I'm doing now is all on the bulkheads and major walls. The washer and dryer closet opening is sized such that the equipment can come out if need be, but otherwise none of these should need removing until the next major refit 50 years from now.