Welcome to the Hatteras Owners Forum & Gallery. Sign Up or Login

Enter partial or full part description to search the Hatteras/Cabo parts catalog (for example: breaker or gauge)
+ Post New Thread
Page 1 of 957 1 2 3 11 51 101 501 ... LastLast
Threads 1 to 20 of 19131

Forum: Hatteras Tech Talk

Techinical Discussion & Hatteras Related Topics Only

  1.   Sticky Threads  

  2. Sticky Thread Sticky: Acceptable Use Policy & Posting Guidelines

    Hatteras Talk Guidelines This section of the forum is for the more technical threads and topics specifically related to Hatteras yachts. Threads in this section should STAY ON TOPIC. Hatteras Owners Forum Acceptable Use Policy & Guidelines Listed below are some expectations that...

    Started by administrator‎, 08-21-2006 09:10 AM
    • Replies: 0
    • Views: 14,482
    08-21-2006, 09:10 AM Go to last post
  3.   Normal Threads  

  1. All Fuel Gauges Inop

    The gauges to my belly tank and two saddle tanks on a 1974 46' Hatteras Convertible are inoperative regardless of fuel level. I am a new Hatteras owner having moved up from a 28' Bayliner so I am unfamiliar with "common gripes" that these boats might have. If it is a common thing, is there a...

    Started by jason.erbecker‎, Today 08:16 AM
    • Replies: 7
    • Views: 92
    Today, 04:35 PM Go to last post
  2. Dip Stick calibration

    I finally got a chance to calibrate a dip stick while fueling this morning. I ve only done the fwd tank. Aft tank is almost empty but I need to clean it up before using. When the boat was on the hard I had both tanks pumped and cleaned but because the boat was blocked slightly now high there is...

    Started by Pascal‎, Today 04:27 PM
    • Replies: 0
    • Views: 13
    Today, 04:27 PM Go to last post
  3. Morning funny

    Here you go

    Started by SEVEN‎, 08-25-2017 06:04 AM
    1067 Pages
    1 2 3 ... 1067
    • Replies: 10,665
    • Views: 540,848
    Today, 03:57 PM Go to last post
  4. Best practice for strainer wingnuts

    Hey gang.Just looking for some help with the maintenance on my saltwater cooling strainers.I can get them opened and cleaned out but I canít seem to get a good fit then seal when putting them back which is getting me water in the bilge when running them.Is there a trick to seating them or a proper...

    Started by hattieice‎, Today 03:23 PM
    • Replies: 3
    • Views: 23
    Today, 03:37 PM Go to last post
  5. Reserve fuel tank is over full

    On my 1984 43MY the reserve tank keeps getting over full when I havenít added fuel. The only thing I can think of is that fuel is somehow bleeding down from the main tank. Maybe leaking by the the fuel selector ball valves? Anything else possible? I think this may be causing a diesel smell in the...

    Started by gmcop1‎, 04-02-2020 07:58 PM
    • Replies: 5
    • Views: 171
    Today, 03:35 PM Go to last post
  6. Sole Linear Feet for 53'?

    Hey all you Quarantined "HATTZMatters", thinking of going forward replacing the sole in No Regrets w/ Lonseal teak & holly but trying to figure out amount to order. Planning on saloon, and all compartments/ passageways below. If someone has done this (I'm sure), what was the total linear foot you...

    Started by Entonces‎, Today 11:17 AM
    • Replies: 4
    • Views: 71
    Today, 01:50 PM Go to last post
  7. Refrigerator...Scratching My Head...

    Ref: Summit Brand Refrigerator, Model HS2961 (This is a unit with NO freezer.) (The new equivalent model is FFAR10, the company is now called the AccuCold Division of Felix Storch) The compressor is an Embraco EMU 45HSC When we bought the boat a little over a year ago the...

    Started by Nick in Manitou‎, 04-02-2020 09:51 PM
    2 Pages
    1 2
    • Replies: 14
    • Views: 351
    Today, 11:55 AM Go to last post
  8. All Detroit Diesel Kids, need your engine data

    All Detroit Diesel Kids I’m finishing up my personal notes on Detroit 2 stroke tune parameters. I hope to combine this data and insert it into my final notes (maybe book). Please reply with your engine model, supposed tune HP, injector size or part number, turbo spec or part number...

    Started by Captain Ralph‎, 03-07-2020 12:36 AM
    • Replies: 6
    • Views: 477
    Today, 08:55 AM Go to last post
  9. 1967 31C OE wiring

    Slowly getting rid of old dead end wiring, next to Port engine there appears to be 2 Fiberglass tanks that were removed. There is also a pair of what appear to be 12 Volt "Checking later" could they be part of the Generator that was also removed at some point. Wiring diagram only shows the...

    Started by Dazed338‎, Yesterday 05:26 PM
    • Replies: 2
    • Views: 64
    Yesterday, 09:07 PM Go to last post
  10. Upper Deck Hatch 58 LRC

    A weird thing happended last Friday.... I was struggling with repairs my shirk wrap in 50 MPH+ winds here in Mystic. I had the hatch open when I climbed on top of the flybridge pilot station to secure the shrink wrap. THe boat heeled over from a wind gust and I braced myself on the open hatch.......

    Started by JD5652‎, Yesterday 08:53 AM
    • Replies: 1
    • Views: 107
    Yesterday, 08:11 PM Go to last post
  11. Leak in Salon Icemaker Water Line

    The original wet bar and sink in my Hatteras 1966 50MY is inside the salon, starboard side aft. I have a slow leak wetting the carpet toward the centerline. Pulled the U-Line icemaker halfway out (it's heavy!). The waterline is a clear plastic hose going from the hose connector at the front of...

    Started by Fanfare‎, Yesterday 02:50 PM
    • Replies: 1
    • Views: 63
    Yesterday, 05:34 PM Go to last post
  12. 65 Hatteras 16v92 ddec2 1993 power loss water in raycor

    To start out went out on sea trial my starboard engine wouldnít accelerate no power. Went to ck found water in raycors. I drained water. Switched tanks to cockpit tank where port engine is running fine on no problem. I changed raycors primary and secondary. I have nice pink fuel in bowls. Engine...

    Started by Wcampan676‎, 04-04-2020 02:06 PM
    • Replies: 8
    • Views: 224
    Yesterday, 04:08 PM Go to last post
  13. Screen Spline with a Sweeper Blade

    My 63 MY has sliding screen frames on the salon windows. On the vertical edge the screen spline has a 3/4" sweeper blade that seals against the glass to prevent insects from making an end run around the screen. I do not know if this is original or a PO add. Anyone have these and know a source for...

    Started by divert00‎, 03-31-2020 03:31 PM
    • Replies: 5
    • Views: 166
    Yesterday, 01:58 PM Go to last post
  14. Aft bulkhead repair/replacement

    Tore out our old tackle locker and found the bulkhead pretty well rotted. Mostly the sides but also behind the bait freezer and under the window. Anyone done this project? Looks like it's 3/4 and 1/2" ply laminated together. The top of the ply is tabbed to the bridge bottom but I can't tell where...

    Started by rsmith‎, 11-18-2018 08:48 AM
    5 Pages
    1 2 3 ... 5
    • Replies: 42
    • Views: 2,535
    Yesterday, 09:22 AM Go to last post
  15. Fuse holder caps

    I need a couple of fuse holder caps for my engine monitor. You canít buy the old style holders. This is for my 1984 43íMY. Thanks, Gary

    Started by gmcop1‎, 04-02-2020 11:47 AM
    • Replies: 5
    • Views: 163
    04-04-2020, 11:47 AM Go to last post
  16. Air compressor dumb question..

    I need to purchase a small 12v tire inflator for the car and just saw one that is both 12volt and 120 volt. Is there any reason I couldn't use this compressor to pressurize the onboard tank without having to start the motor?

    Started by Oldlaxer1‎, 04-02-2020 08:07 AM
    2 Pages
    1 2
    • Replies: 13
    • Views: 361
    04-04-2020, 10:14 AM Go to last post
  17. Tried the Hx Cleaning Method

    recommended by Genesis (who remembers him?) for the first time yesterday. Fairly easy and inexpensive. After, I ran the engines for 10 minutes and then a fresh water flush to get the salt out. I then drained the raw water side, leaving it empty until next start up This got me thinking. Now...

    Started by Passages‎, 04-02-2020 08:21 PM
    • Replies: 4
    • Views: 242
    04-04-2020, 09:57 AM Go to last post
  18. 16v92 Ddec 2 on 65 Hatteras power loss

    My starboard engine all of a sudden wonít go over 800 rpm in gear. When in neutral it slowly responds up in Rpm. Very slow power loss. Do these Ddec have a safe mode. Any help. Check engine lite on code 46 probably cause battery charger went bad 2 months ago and code 55

    Started by Wcampan676‎, 04-01-2020 10:57 PM
    • Replies: 9
    • Views: 416
    04-03-2020, 10:12 PM Go to last post
  19. Engine raw water system

    Question, on my DD 8V92, the raw water system pumps water through the inter cooler, fuel cooler, heat exchanger, through a pipe with a T fitting, into the shower head . The T fitting allows water out the side through a valve. What is the purpose. Thank you P.

    Started by osprey‎, 04-01-2020 04:42 AM
    • Replies: 3
    • Views: 155
    04-03-2020, 09:39 PM Go to last post
  20. Transom zinc

    I can't find the receipt or part# for my transom zinc. I know it was over$100 at old marina and boat zinc . com doesn't show what I think it looked like.

    Started by MadHatter53‎, 04-02-2020 03:41 PM
    • Replies: 3
    • Views: 123
    04-03-2020, 12:07 PM Go to last post

Forum Information and Options

Moderators of this Forum
Users Browsing this Forum

There are currently 112 users browsing this forum. (4 members & 108 guests)

  1. Nick in Manitou
  2. ShaunThrives
  3. RonNP
  4. Wcampan676

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 15 replies or 150 views
Hot thread with unread posts
More than 15 replies or 150 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts