Has anyone upgraded their old mechanical gyro Naiads to the newer digital controls? I'm in the process now and wondered how much improvement was realized.
Welcome to the Hatteras Owners Forum & Gallery. Sign Up or Login
+ Reply to Thread
Results 1 to 10 of 12
-
Upgrading Naiad stabilzers to digital controls
Sky Cheney
1985 53EDMY, Hull #CN759, "Rebecca"
ELYC on White Lake--Montague, MI
-
03-27-2024 07:01 AM #2
Re: Upgrading Naiad stabilzers to digital controls
Following
I was quoted about $20K is that close?Dave & Trina
Benedetto
1989 60MY HATDK310
Sturgeon Bay/Ft. Lauderdale
-
Re: Upgrading Naiad stabilzers to digital controls
Sky Cheney
1985 53EDMY, Hull #CN759, "Rebecca"
ELYC on White Lake--Montague, MI
-
Re: Upgrading Naiad stabilzers to digital controls
When I put mine in 3 years ago they came with the Multisea controls and I could have had the full digital control for about $5000 more but the Naiad guys did not think it was worth the extra money. I have been on 2 boats now with the Multisea controls and neither one, including mine could they get the slow speed cut off feature to work from a GPS input and I had at the time a brand new Garmin MFD.
Mahalo V
1974 53 Motoryacht
Hull Number 406
San Diego, Ca. Ready 32 Nordic Tug, Brunswick Ga.
-
03-27-2024 03:15 PM #5
Re: Upgrading Naiad stabilzers to digital controls
My feedback from Naiad was the same about not much difference in control and I did not do with the digital controls either during my install in 2022.
My slow speed cut off feature does work with my Garmin. Anything below 3 knots and it goes into STANDBY and then automatically resumes control when speed increases about 3 knots.JD
1976 58' LRC Hull #311
"Miss Maggie"
Riviera Dunes, FL
-
Re: Upgrading Naiad stabilzers to digital controls
I'm not to familiar with these digital controls.
Just once helping on a boat that got hit by lightning. What an expensive mess.
Questions; Is it a big deal for auto cut off below 3 kts?
What other benefits does a digital controller offer?
Anything worth more than 5 bux vs manually pushing the center button manually?
-
03-27-2024 05:00 PM #7
Re: Upgrading Naiad stabilzers to digital controls
My understanding is that the stabilizer fins are basically non-effective below 3 knots and the system is basically just thrashing about. Pushing the CENTER button would achieve the same result.
My perspective is that most captains are too busy with other "things" to consistently monitor vessel speed to the point when it's below 3 knots and the thought is to CENTER the fins.... but that's just conjecture on my part....JD
1976 58' LRC Hull #311
"Miss Maggie"
Riviera Dunes, FL
-
Re: Upgrading Naiad stabilzers to digital controls
Going from a mechanical gyro to a modern multi-axis electronic control gives you more than just a system that senses roll once it has started. It looks at roll, pitch, and yaw which is necessary to stabilize in following seas. The newer controls, including the multi-sea, also allow for sensitivity and trim adjustment at the helm while underway. With the digital control, any other adjustment can be made in the programming setup including the centering and acceleration, stops, etc to each individual fin. With the old hydraulic gyro there was just a tee in the line so both fins reacted the same.
Plus, the digital controls record the fin response and compare it to the output from the computer. A log is kept to see how close the fins follow what they were commanded to do. This information can be used to further tweak the system and get it dialed in. It can be downloaded and sent to the manufacturer if needed.
Another feature is an automatic sensitivity adjustment that changes depending the vessel speed. So there are plenty of pluses to the upgrade beside programmable centering minimum and maximum limits . Not to mention the fewer hydraulic lines and no feedback assemblies to leak and maintain.Last edited by SKYCHENEY; 03-27-2024 at 05:29 PM.
Sky Cheney
1985 53EDMY, Hull #CN759, "Rebecca"
ELYC on White Lake--Montague, MI
-
-