I'd replace them. By the time you clean them up you'll have spent more in your time. Soraht
Y
Spray the new ones with corrosions
Welcome to the Hatteras Owners Forum & Gallery. Sign Up or Login
+ Reply to Thread
Results 11 to 20 of 59
-
Re: How would YOU address these and how immediate?
-
Re: How would YOU address these and how immediate?
The rudder gland has been messed with because there's stainless nylock nuts on the hull bolts and I think also on the packing gland bolts. Also the green ground wire looks new and appears to be undersized, heat shrink connector should have been used. What does the other rudder port look like?
Wouldn't trust that strainer at all, something else must be going on there besides just neglect. When you get it out of the water don't be scared to use the torch to get things apart, I like the gas in the yellow can.CRICKET
1966 HAT50C101
Purchased 1985 12v71Ns
Repowered 1989 with 8v92TI
Repowered 2001 with 3406E
-
Re: How would YOU address these and how immediate?
I would question other areas as well. If an owner doesn't maintain the rudders and strainers I would wonder how often he changed oil, coolant, transmission fluid etc. The others are right, replace them to be safe.
SEVEN
1979 53' MY Hull #563
Antioch, California
-
06-23-2017 06:31 PM #14
Re: How would YOU address these and how immediate?
The rudder stuffing box may need a closer inspection. It doesn't appear to be leaking, but you have to wonder about the condition of the shaft packing and the cutlass bearings since it hasn't been touched in a long time. If its been sitting for a while you would probably loosen it up a bit on a run that long and it may start leaking. Also, I would look at the condition of the box to hull mounting hardware and the mounting studs and nuts for the packing seal. If those are giving way you would be in a bad position offshore.
On the strainer I would check if the valve is working and if so I would run it.
We did every single strainer (this was a major job) / through hull / valve on our boat about 4 years ago. They were in very poor condition. That said though the boat made it from California to Washington without an issue in that condition.
Have you looked at the shaft stuffing boxes as well? I'm curious what condition they are in. That is another area to look at.
-
06-23-2017 06:38 PM #15
Re: How would YOU address these and how immediate?
I think from a purchase decision standpoint this is spot on. I would want to see maintenance logs and that sort of thing to know what I am getting into. At the end of the day though a lot of us are working on boats that are 30+ years old so there is always going to be some issues. The boats that were /are *that* bad I would expect are no longer functioning. Then again we all have a few of those questionable boats in the marina.
-
06-23-2017 06:40 PM #16
-
Re: How would YOU address these and how immediate?
You ought to clean the corrosion off and have a better look. A mild acid like vinegar or lemon juice will work. At the least, check the packing in the glands and refresh if needed. These can begin to leak pretty fast if the seal is being helped by the corrosion. It's easy to add/refresh the gland packing. Do the ball valves work? If so, you can close and clean strainers in the water and see if they can seal back up. If you loose the seal on a strainer underway you will start sucking air.... not good.
Bobk
-
Re: How would YOU address these and how immediate?
As to making a 600 mile run, the question is where? In the ICW where help is easily available, maybe. Off shore, no I would not. Where is the boat now?
Bobk
-
Re: How would YOU address these and how immediate?
SEVEN
1979 53' MY Hull #563
Antioch, California
-
06-23-2017 10:44 PM #20Senior Member
- Join Date
- Jan 2017
- Posts
- 362
Re: How would YOU address these and how immediate?
Such a nice guy
Last edited by Seapig100; 06-25-2017 at 07:01 AM.