Jim, I've noticed a pattern in which I announce a big job coming up soon, then once the big job is done you mentioned how you'd like to come visit the boat. LOL
Welcome to the Hatteras Owners Forum & Gallery. Sign Up or Login
+ Reply to Thread
Results 1,161 to 1,170 of 1855
Thread: 1969 Chris Craft Roamer 46 refit
-
08-01-2018 07:47 PM #1161Senior Member
- Join Date
- Nov 2008
- Posts
- 1,677
Re: 1969 Chris Craft Roamer 46 refit
-
Re: 1969 Chris Craft Roamer 46 refit
SEVEN
1979 53' MY Hull #563
Antioch, California
-
Re: 1969 Chris Craft Roamer 46 refit
well, duh. You don't expect me to WORK do you? C'mon now
-
08-02-2018 07:59 PM #1164Senior Member
- Join Date
- Nov 2008
- Posts
- 1,677
Re: 1969 Chris Craft Roamer 46 refit
Work?
It's not work! It's loooooove!
-
08-08-2018 08:32 AM #1165Senior Member
- Join Date
- Nov 2008
- Posts
- 1,677
Re: 1969 Chris Craft Roamer 46 refit
Speaking of love...
I'm back at work inside the boat, finishing up the inside of the salon cabinet. It's brutally hot and humid though, so there's a limit to how much I can do since I'm working with wood. Dripping sweat makes it hard to get the job done. But I'm making progress and should be able to wrap this up soon.
1969 Chris Craft Roamer 46 Refit: Back Into the Starboard Salon Cabinetry
Cheers,
Q
-
08-10-2018 09:58 AM #1166Senior Member
- Join Date
- Nov 2008
- Posts
- 1,677
Re: 1969 Chris Craft Roamer 46 refit
I spent more time than I wanted to inside the cabinetry again, cleaning up the engine room blower outlet. Water had gotten under the barrier coat, so there was a lot of aluminum oxide to clean up before I coated the whole thing with epoxy. Once that was done, I was able to install another insulated plywood panel inside the cabinet. I've only got one more to go, and this part of the project will be done. Boo
1969 Chris Craft Roamer 46 Refit: Still Inside the Starboard Salon Cabinetry
Cheers,
Q
Before
After
-
08-10-2018 08:51 PM #1167Senior Member
- Join Date
- Nov 2006
- Posts
- 1,219
Re: 1969 Chris Craft Roamer 46 refit
Hey Quentin—great stuff (as usual).
I’ve got some blistering under the paint on my aluminum radar arch, but had not considered epoxy coating to reseal.
What are your expectations/experience with longevity for that approach?
DAN
-
08-11-2018 06:16 AM #1168Senior Member
- Join Date
- Nov 2008
- Posts
- 1,677
Re: 1969 Chris Craft Roamer 46 refit
Thanks, Dan!
I think epoxy works fine in places that don't get direct sun exposure. West System has a hardener that provides UV protection, but without that the coating will break down over time from sunlight. For a radar arch, I'd sand to bright metal, hit it with alumaprep and alodine, power wash to remove every hint of those chemicals, then prime with Awlgrip's aluminum primer followed by 545 and the topcoat. I recently heard that simply washing off the alumaprep and alodine (even using a stiff bristle brush) isn't enough to remove every trace of the chemical. If any trace remains, as the sun hits the topcoat and heats it up, the residue causes a blister. Power washing seems to be the solution to that problem.
-
08-12-2018 02:56 PM #1169Senior Member
- Join Date
- Nov 2006
- Posts
- 1,219
Re: 1969 Chris Craft Roamer 46 refit
Great input—sounds suspiciously like what may have been the problem in the first place!
I approve this project. My boat will be ready for you to commence as soon as you fly out...
DAN
-
08-12-2018 07:27 PM #1170Senior Member
- Join Date
- Nov 2008
- Posts
- 1,677
Re: 1969 Chris Craft Roamer 46 refit
Sounds good.
I'll be there just as soon as the private jet arrives along with the 6-figure cashier's check...and I'm talking 'significant figures' for both the check and the stewardesses on the plane!