it is beautiful!!!
Welcome to the Hatteras Owners Forum & Gallery. Sign Up or Login
+ Reply to Thread
Results 951 to 960 of 1855
Thread: 1969 Chris Craft Roamer 46 refit
-
05-31-2017 12:10 PM #951Senior Member
- Join Date
- Apr 2005
- Posts
- 185
Re: 1969 Chris Craft Roamer 46 refit
-
Re: 1969 Chris Craft Roamer 46 refit
Looks amazing. Can't wait to see the entire interior. I'd pay for that tour.
-
06-01-2017 07:50 AM #953Senior Member
- Join Date
- Nov 2008
- Posts
- 1,677
-
06-02-2017 09:00 AM #954Senior Member
- Join Date
- Nov 2008
- Posts
- 1,677
Re: 1969 Chris Craft Roamer 46 refit
This isn't directly related to my boat refit, but it's one of many things that's happened this year that contributes to the boat not splashing.
The transmission went out in my truck late last year. $3500 later, the tranny was working fine, but a month later the engine started sounding like it was coming apart. We barely made it home, and a compression test revealed low compression. Codes indicated bad catalytic converters. Dents on the exhaust pipe indicated the tranny shop had beaten hard on the exhaust, which might have caused the cats to fracture and come apart, blocking the exhaust system and sending ceramic particles up into the cylinders. With new cats in, the truck ran OK but still had low compression on a few cylinders. But recently I tested it again and found the compression was restored! 190~200psi in all cylinders! Here's hoping the magic that fixed the truck gets sprinkled on the boat. It'd be good to have things go my way after some of the unfortunate things that have happened over the years to delay the project.
1969 Chris Craft Roamer 46 Refit: My Life WAS An Old-School Country Western Song
Cheers
Q
-
06-07-2017 10:12 AM #955Senior Member
- Join Date
- Nov 2008
- Posts
- 1,677
Re: 1969 Chris Craft Roamer 46 refit
Back to boat stuff...
I got the starboard V-berth panel installed! WOOHOO!!
Those two curved panels were the biggest interior challenge I've knocked out so far. I am sooooo glad to be done with them. It's starting to look like a boat interior again!
1969 Chris Craft Roamer 46 Refit: Installing the Starboard V-berth Mahogany Wall Panel
Cheers,
Q
-
Re: 1969 Chris Craft Roamer 46 refit
Almost a 1,000 replays. Has to be a record?
SEVEN
1979 53' MY Hull #563
Antioch, California
-
06-09-2017 09:25 AM #957Senior Member
- Join Date
- Nov 2008
- Posts
- 1,677
Re: 1969 Chris Craft Roamer 46 refit
I'm goin' as fast as I can, dude!!! lol
With those PITA curvy V-berth walls finally installed, the rest of the cabinetry in that room is coming together relatively quickly. It's looking more and more like a motor yacht interior with each passing weekend.
1969 Chris Craft Roamer 46 Refit: Fitting the V-berth Cabinets
Cheers,
Q
-
06-16-2017 10:39 AM #958Senior Member
- Join Date
- Nov 2008
- Posts
- 1,677
Re: 1969 Chris Craft Roamer 46 refit
I finished fitting the panels, cut the top cabinet panel, and then started doing the final preparation for installation. With sticky epoxy everywhere, it's best to just leave the area and come back when it cures.
1969 Chris Craft Roamer 46 Refit: More V-berth Cabinetry
Cheers,
Q
-
06-22-2017 12:17 PM #959Senior Member
- Join Date
- Nov 2008
- Posts
- 1,677
Re: 1969 Chris Craft Roamer 46 refit
I've been learning more about making cabinets. I think I've got the process finally worked out, but it's challenging stuff. It doesn't help that I'm using epoxy and even on mild days the temperature in the tent is way above 100°F. Getting all the pieces wetted out and put together before the epoxy kicks isn't easy. But so far it's going pretty good.
1969 Chris Craft Roamer 46 Refit: V-berth Cabinetry Storage Boxes
Cheers,
Q
-
Re: 1969 Chris Craft Roamer 46 refit
What is the pot life on the ICA poly?