My bottom was soda blasted in the fall and over the winter I've stripped and polished all my bronze intake strainers. My wedge strainers were covered with growth and I'm not sure if the PO ever took them off. Every time the boat comes out of the water the hull is clean but all bronze parts are covered. I've tried several zinc spray products with no luck. Is there anything I can use to help combat growth on bronze parts? I'd like to try something different since I'm starting from scratch.
Welcome to the Hatteras Owners Forum & Gallery. Sign Up or Login
+ Reply to Thread
Results 1 to 10 of 11
Thread: Underwater Metals Prep and Paint
-
03-10-2011 10:19 PM #1
Underwater Metals Prep and Paint
-
Re: Underwater Metals Prep and Paint
THere are a lot of products that CLAIM to solve the problem but I haven't yet managed to find any that actually do. But it may have to do with the location - some waters are "friendlier" than others as far as barnacles, marine growth, etc.
Mike P
San Miguel de Allende, Mexico; Kent Island MD; San Antonio TX
1980 53MY "Brigadoon"
-
03-10-2011 10:52 PM #3
Senior Member
- Join Date
- Jan 2010
- Posts
- 133
Re: Underwater Metals Prep and Paint
I use my boat every day and my metals still got LOADED. This went on for years!
I finally got aggrevated and called Petit directly and took down the part #'s the gent on the phone recommended and haven't had a barnacle since!
On bare metals you need to use an etching primer first.
Second the Petit metal primer (I forgot the name, but it's orange).
Third coat is old school HARD bottom paint. Trinidad 75% copper!
I wish I did it years ago. AND I'VE TRIED EVERYTHING!
-
Re: Underwater Metals Prep and Paint
I have been using Propspeed for 6 years in warm FL water on my props and it works great. We use the boat a lot and even though stuff starts to grow everything falls off within a few minutes. Those with bad results using this let their boats sit for long periods. When the barnacles grow so much that they are all touching they form a casing and that will not come off. Next haulout I am doing all my running gear and rudders with it.
-
03-12-2011 08:47 AM #5
Senior Member
- Join Date
- Apr 2005
- Posts
- 4,168
Re: Underwater Metals Prep and Paint
Checking with a paint company seems a good way to go as their paint formulations likely vary be region and country.
I once gabbed with a couple of guys taking photos of a dozen or so underwater paint swatches on the the bottom of a sailboat hauled in my marina...they were testing antifouling in Long Island Sound, NY, for International Paint Company....and they said they used different formulations in other parts of the country.
(Warning: This may be "invalid" information according to rsmith because he would claim I did not "experience" this test personally....it's therefore only "hearsay")
Also good to ask if the paint for strainers and other metals works better with or without cathodic bonding......zincs. You don't need bonding on quality silicon bronze strainers, but if you want to use it, it's quite possible a different paint formulation would be recommended.
Does any company make marelon or other "plastic" strainers????Rob Brueckner
former 1972 48ft YF, 'Lazy Days'
Boating isn't a matter of life and death: it's more important than that.
-
Re: Underwater Metals Prep and Paint
I have used the system above for years in West central Florida for years. It is bullet proof IF you follow the surface prep, dry time and re-coat times on the products precisely.
Be sure to mask both ends of the cutlass bearings (I use small diameter cord) or all these repeated coats of paint will plug the water slots and ruin the bearings.
-
03-15-2011 11:43 AM #7
Re: Underwater Metals Prep and Paint
I'm in R.I. Way up Narragansett bay. During the summer months the water gets into the low to mid 70s. That's when we get high fowl conditions up here. The last two years we've had above average rainfall and it's made the the barnicals grow even faster than normal. I'm using Interlux products to barrier coat the hull they have a similar etching primer combo. I'm looking online at Petits underwater metals kit. Is this what your referring to the box is orange but it makes no note of the primer color? I still have a few weeks before I can even think of getting started. I'd like to research it a little more before I make a purchase. For once it's not a big rush. But it will be if I don't get moving. I've contacted Iterlux and of course ther telling me there product is superior to Petits and that's what I'd expect to here from any competent company man. However I've heard nothing to back it up. Has anyone used the Interlux etch product? Please advise
Jim
-
Re: Underwater Metals Prep and Paint
As said its not the antifoul properties of the paint but getting it to stick. I find that a light sandblast of the metal helps hold the etch and primer better. Also if you dont keep up on your zinks up the electrolisis will blast the paint off like a torch.
"DON'T BELIEVE ANYTHING YOU READ OR HEAR AND ONLY HALF OF WHAT YOU SEE" - BEN FRANKLIN
Endless Summer
1967 50c 12/71n DDA 525hp
ex Miss Betsy
owners:
Howard P. Miller 1967-1974
Richard F Hull 1974-1976
Robert J. & R.Scott Smith 1976-present
-
Re: Underwater Metals Prep and Paint
I'll try to find out the name of the zinc spray that Smith's Marina is using on my boats underwater metal parts. It has helped quite a bit. They are not totally free of barnacles but if I run the boat every week, which I ought to do anyway, they stay pretty clean.
-
03-15-2011 09:57 PM #10
Senior Member
- Join Date
- Apr 2005
- Posts
- 2,771
Re: Underwater Metals Prep and Paint
I've had pretty decent success from the use of Zinc sprays, but in order to work it needs several coats as a single coat is so thin that in no time at all the little critters start hanging on. Three or four coats seems to work fine, probably more coats would be better. Also you don't need to buy the "marine" zinc paint for 20 some $ as the much cheaper off the shelf at Home Cheapo works as well at a fraction of the cost.
Walt