The PO used to dock on his own, i.e. single-handle, and right over some pilings. Therefore the bottom half of many stbd side portholes are broken out or chipped away. Not a hazard to water ingress, but uglyanyway, plus the surveyors ding them/me
At any rate, since Fuller Brush is now willing to sell pieces parts I would only need to replace the liner shell throughhull from the interior to the exterior, plus probably the piece of exterior trim that sits flat on the hull around the porthole.
Long preamble, short question. What will be the most difficult aspect of doing the R&R. Is the shell bonded in, or the exterior trim bonded on like crazy.
What's my worse case effort area? Time for one of those new highspeed buzzer cutters, etc.?
Welcome to the Hatteras Owners Forum & Gallery. Sign Up or Login
+ Reply to Thread
Results 1 to 10 of 19
-
Fuller Brush Portholes Replacement
50 Years on the Great Lakes...
-
Re: Fuller Brush Portholes Replacement
I have done all 6 in our boat. It would be next to impossible without a Fein Multimaster. I used the multimaster to cut under the trim ring and cut the 5200 that was many years old as well as cut the 5200 that held in the porthole itself. I woudl estimate about 1 to 2 hours per porthose with cleanup. Could be less if you have someone to help you. I had help, so it took a little more than 1/2 a day to do all 6, but we were pros by the time we did the last one.
Pat Bustle
Palmetto, Florida
1984 38 Topaz Express "Aranmore"
Broker, United Yacht Sales
Visit My Website
-
Re: Fuller Brush Portholes Replacement
I've used a Fein Multimaster (borrowed from Dr Jim) and agree it's a superb tool and would be invaluable for the work you are talking about. But one of the guys that does a lot of boat work at our marina recently bought a Dremel version of the same thing (I didn't know it existed until I saw him using it) that he swears by and, as he put it, "Why pay 300 bucks for something you can buy for 100 bucks?"
I am not suggesting that the Dremel is equal in quality - based on the price difference, I'm sure it is not though since the Fein is made in Europe, the Euro/dollar ratio works against it a bit. It might be worth looking into the dremel - this guy does a LOT of boat work with it. I don't own either one and I have not personally used the dremel so I can't directly compare them.
I will be pulling the aft windows from the master stateroom this season and expect to be using one of those two tools to do so!Mike P
San Miguel de Allende, Mexico; Kent Island MD; San Antonio TX
1980 53MY "Brigadoon"
-
Re: Fuller Brush Portholes Replacement
Ed did that exact same job (replaced the main part that goes through the hull and the trim ring) on the master stateroom portlight that a StinkRay took out while docking when he backed into my portlight and broke off the part that protrudes out from the hull a little bit. He didn't have that nice tool (but he does now!). As I recall, he got it out without too much headache using a scraper. But if you have more than just the one to do, you really should get the tool. I do recall him saying how much easier and faster it would have been with the tool.
-
Re: Fuller Brush Portholes Replacement
I have not used the Fein tool, but the $39 Harbor Freight version works great. I highly recommend that type of tool for cutting 5200. I used it to get my power inlet surrounds off and it was a huge time saver.
Sky Cheney
1985 53EDMY, Hull #CN759, "Rebecca"
ELYC on White Lake--Montague, MI
-
04-19-2010 12:41 PM #6
Re: Fuller Brush Portholes Replacement
I have one to do too...WTF is a Fein Multimaster? And what is the Harbor Freight one called? I figure for doing ONE...the HF version should be adequate.
Dave
"Saraswati" - 1980 53MY
Galesville, MD
-
Re: Fuller Brush Portholes Replacement
Here's a test of the Fein plus the Dremel and the Bosch version of same.
http://www.toolsnob.com/archives/200...ax_oscilla.phpMike P
San Miguel de Allende, Mexico; Kent Island MD; San Antonio TX
1980 53MY "Brigadoon"
-
Re: Fuller Brush Portholes Replacement
Sky Cheney
1985 53EDMY, Hull #CN759, "Rebecca"
ELYC on White Lake--Montague, MI
-
04-19-2010 10:09 PM #9Senior Member
- Join Date
- Feb 2006
- Posts
- 173
Re: Fuller Brush Portholes Replacement
I've changed quite a few of mine too. Fortunately, they were able to come out without cutting anything. Just worked a putty knife in from the outside after prying off the ring.
Two things to consider on installing the new ones. I cut mine off even with the outside ring so that they wouldn't break again and or be pushed in by a low fender. I know it takes away from the original look but functionally they are much better.
Second, consider NOT using screws to attach the new outside rings. The caulk is sufficient to hold them in place (tape till dry). Then you don't have screws that seem to always attract rust.1987 63' CPMY - Jubilee
Tampa, FL
All who wander are not lost.
-
Re: Fuller Brush Portholes Replacement
I read the reviews, plus the blog posts and the separate Rockwell review. Surprised they had not heard of Rockwell. I thought they were a commercial grade of old-line tools.
The review is from 2008, so maybe there are upgraded reviews, but I have not looked. I have had Bosch tools, which have been excellent, but the review did not like the 8min life of the 12v batt. Maybe they are up to the 18v now with LithIon.
So I'll check some more.
Good to know that the Fein/et al are needed to do this. I have a small air vent cover I have not been able to get off, because of the 5200, so I will try the tool (whatever I buy) on that.
If anyone has any more info, please post!50 Years on the Great Lakes...