Welcome to the Hatteras Owners Forum & Gallery. Sign Up or Login

Enter partial or full part description to search the Hatteras/Cabo parts catalog (for example: breaker or gauge)
+ Post New Thread
Page 1 of 1107 1 2 3 11 51 101 501 1001 ... LastLast
Threads 1 to 20 of 22126

Forum: Hatteras Tech Talk

Techinical Discussion & Hatteras Related Topics Only

  1.   Sticky Threads  

  2. Sticky Thread Sticky: Acceptable Use Policy & Posting Guidelines

    Hatteras Talk Guidelines This section of the forum is for the more technical threads and topics specifically related to Hatteras yachts. Threads in this section should STAY ON TOPIC. Hatteras Owners Forum Acceptable Use Policy & Guidelines Listed below are some expectations that...

    Started by administrator‎, 08-21-2006 09:10 AM
    • Replies: 0
    • Views: 19,614
    08-21-2006, 09:10 AM Go to last post
  3.   Normal Threads  

  1. Oiling Walker Air Seps

    I have just cleaned my Walker Air Sep filters. Difficult to buy Walker products here. What alternate oil can I use to oil them? WD40 seems too easy but will also do the job?

    Started by scottinsydney‎, Yesterday 11:38 PM
    • Replies: 3
    • Views: 41
    Today, 07:23 AM Go to last post
  2. Morning funny

    Here you go

    Started by SEVEN‎, 08-25-2017 06:04 AM
    3684 Pages
    1 2 3 ... 3684
    • Replies: 36,834
    • Views: 4,367,784
    Today, 12:03 AM Go to last post
  3. Help with these Isolation Transformers (assuming that is what they are)

    I have 2 large boxes in the engine room (see below) which I believe to be isolation transformers as well as possibly voltage boosters/frequency converters. Of all the documentation I have on board, I don't have any information on these. I've attached a photo of the top unit and hope maybe...

    Started by zigzag930‎, 10-30-2022 02:21 PM
    3 Pages
    1 2 3
    • Replies: 21
    • Views: 1,730
    Yesterday, 11:50 PM Go to last post
  4. 58 LRC exterior wall construction

    Hello everyone,I am in the process of rebuilding the half of my aft salon wall that was removed years ago. I have found that there is a 2” x 4” stud in the part of the wall that is left in place but I am not sure what type of wood it is. Does anyone know what type of wood Hatteras used for the...

    Started by BFDfirefighter16‎, Yesterday 09:44 PM
    • Replies: 0
    • Views: 38
    Yesterday, 09:44 PM Go to last post
  5. Muriatic Acid or Vinegar for Galley Maid heads/hoses

    Our Master SR head went from working perfectly to not discharging virtually overnight. I thought perhaps the stator or rotor in the 32v pump failed, but when I pulled the vent plug and filled it with water, the pump sucked it right out quickly. So I figured that means the hose from the head to...

    Started by zigzag930‎, 05-17-2024 04:06 PM
    • Replies: 6
    • Views: 128
    Yesterday, 02:37 PM Go to last post
  6. What is this Electrical Part

    There are three of these oversize relay type parts in the lower section of our AC Distribution Panel. They seem to click a bit when the genset is switching on/off or when we switch to the inverter. Given there are three AC sub panels, I guess there is one gizmo for each. I showed this ...

    Started by scottinsydney‎, 05-08-2024 08:54 PM
    • Replies: 9
    • Views: 308
    Yesterday, 09:06 AM Go to last post
  7. Repair or replace props

    An unfortunate event…. I slightly ran aground on an unmarked shoal. I managed to back off it however, upon arriving at the marina, I had the boat craned out and inspected the hull and the props. The hull was fine but the props are a limited damaged. I contacted my insurance company and started a...

    Started by Phasma2128‎, 05-17-2024 01:23 PM
    • Replies: 5
    • Views: 114
    05-17-2024, 10:38 PM Go to last post
  8. Cool In Frame in 58’ Hatteras

    Can someone tell me if you can do an inframe on Detroit 871 in 58’ Hatteras with dropping oil pan in bildge or if engine must be lifted Thanks Alan

    Started by angeron1@yahoo.com‎, 05-15-2024 05:53 PM
    • Replies: 7
    • Views: 272
    05-17-2024, 03:55 PM Go to last post
  9. Cruisair SMX II thermostat not showing power

    Need help to try and get my thermostat to show it is receiving power. The compressor is receiving power from the breaker, but is not relaying it to the thermostat. Is there a safety switch on the Cruisair that would prevent the thermostat to power up? I have tested this thermostat location with...

    Started by Big Chief‎, 05-16-2024 01:38 PM
    • Replies: 5
    • Views: 118
    05-17-2024, 12:47 PM Go to last post
  10. Compressed air piping

    I’m wondering what others have done to bring compressed air to various parts of your boat. I have had a Milton air products sold system for a few years now but I’d like a system that doesn’t leak as much air, as my electric compressor kicks on probably twice a day to top up the tank. My system...

    Started by bostonhatteras‎, 05-16-2024 07:38 PM
    • Replies: 3
    • Views: 76
    05-16-2024, 09:05 PM Go to last post
  11. 12v71TI Oil Leak

    The starboard engine has always leaked some oil into the bilge. Over the past couple of years this seems to be increasing. Today I now have more than a gallon of oil in the bilge and I have watched the dipstick oil level go down after a recent 4 hour run.. Not good. There is obviously a very...

    Started by scottinsydney‎, 05-07-2024 06:53 AM
    2 Pages
    1 2
    • Replies: 10
    • Views: 354
    05-16-2024, 06:25 PM Go to last post
  12. Radio Recomendations

    Lost main vhf radio. It's old and so rather than repair thought I'd replace. All electronics are old, so no point in matching existing brands as I will probably change all over to Furano later this year. Recomendations, opinions, comments?

    Started by Chasemmc‎, 05-14-2024 11:33 AM
    2 Pages
    1 2
    • Replies: 13
    • Views: 359
    05-16-2024, 01:53 PM Go to last post
  13. Door button

    Does anyone recognize this manufacturers imprint ? P L CO Seems all the units like this are now either zinc or stamped. These are solid SS with substantial spring holding the cross bar.

    Started by bostonhatteras‎, 03-30-2018 06:54 PM
    • Replies: 6
    • Views: 1,450
    05-15-2024, 12:36 PM Go to last post
  14. Dodger board!

    Wondering if anyone has some dodger board detail pics that they can share. Mine need some fixing up, but I have also noticed that some of these boats have a nicer implementation of this feature than others. We have a 1972 43DC and our dodger boards are pretty much just tacked on there with...

    Started by brettportzer‎, 05-14-2024 10:58 AM
    2 Pages
    1 2
    • Replies: 10
    • Views: 278
    05-15-2024, 09:43 AM Go to last post
  15. Boat yards/builders

    I have a 43 Double Cabin. I want to add a cockpit. Can anyone recommend a builder or yard in Louisiana or Alabama that can do a cockpit addition?

    Started by Triskele‎, 05-08-2024 10:59 AM
    • Replies: 8
    • Views: 349
    05-15-2024, 07:36 AM Go to last post
  16. oil change pump

    Hello all, i have a Grocco gpb-1 oil change pump. I went to change the oil over the weekend and its not pulling. Its a gear driven pump that is self priming, has anyone else had this problem, should I try priming it? Thank You!

    Started by workingonadream‎, 05-14-2024 07:25 AM
    • Replies: 5
    • Views: 169
    05-14-2024, 03:06 PM Go to last post
  17. Lonmarine Flooring

    Has anybody used Lonmarine flooring. We're about to re do the master head on our 46c and we need to pull up the flooring to address a soft spot about the size of a quarter. Lonmarine's Teak and Holley looks pretty close to the wood floor in our galley. There is some curvature in the floor so I'm...

    Started by Capt Chad‎, 05-13-2024 08:19 AM
    • Replies: 9
    • Views: 260
    05-14-2024, 11:26 AM Go to last post
  18. Salon window extrusion

    Some mention has been made in various threads about window replacement regarding the fiberglass extrusions that Sam's carries. I will talk to them also, of course, but, I am curious if anyone has any experience with these? They are made of fiberglass, and so I am assuming that you would miter...

    Started by brettportzer‎, 05-14-2024 11:00 AM
    • Replies: 0
    • Views: 76
    05-14-2024, 11:00 AM Go to last post
  19. Another “What is it “ this time galley sink

    Replaced the kitchen sink faucet this weekend. I’ve noticed this drain pipe before and just assumed it was the remnants of an old trash compactor or something since I have an old breaker marked as such. This time I decided to peek down inside and I can see what looks like a bundle of old poly...

    Started by IOLANI‎, 05-12-2024 03:25 PM
    • Replies: 4
    • Views: 230
    05-13-2024, 01:36 PM Go to last post
  20. Best way to prime engines while on the hard.

    I recently had the fitting for the hose on my forward tank going to the distribution manifold fail. Since it was the fitting right at the fuel tank, probably no more fuel was lost than what looks like whatever was in the hose and 1/2 the Racor. So, smelly, but not serious. Let's just say that I am...

    Started by RJM‎, 05-12-2024 12:01 PM
    • Replies: 7
    • Views: 190
    05-12-2024, 08:51 PM Go to last post

Forum Information and Options

Moderators of this Forum
Users Browsing this Forum

There are currently 195 users browsing this forum. (5 members & 190 guests)

  1. whoover
  2. rfontanet
  3. Lmcruiser
  4. Sadey
  5. Jims43DC

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 15 replies or 150 views
Hot thread with unread posts
More than 15 replies or 150 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts